I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello Nordic Support Team
I am working with nrf52832 dk board.I am using mesh sdk version 2.2.0 with nrf sdk version 15.0.0.I am working with uart coexistence example...
I updated the firmware of my Nordic Thingy 52 to the latest version 2.20 using the Android app on my smartphone. Now I cannot use anymore the standard webapp ( https://developer...
I have this problem with all the samples for the nRF9160. When I build the zephyr.elf file, I get an error saying it failed. Please see the picture below. Any idea what's...
Hi,
SDK: nRF52_SDK_12.2.0
Softdevice: Generic_Stack_S332_02.00.01.hex
TX_PIN_NUMBER: on port 25
RX_PIN_NUMBER: on port 26
In our application we are using two...
Hi, We would like to support Bluetooth 5 in an upcoming product development.
Bluetooth 5 gives us two options for an improved connection: Twice the data through put (payload...
Hi,
I am using the Thingy:52 (that contains the nRF52832) and also have evaluation board of nRF52840.
Does anyone have a recommendation for a DAC for use with one of these...
HI,
May I ask, what is the version of J-LINK officially supported in sdk 15.3? I can not find it in release note.
See.
The following toolchains/devices have been used...
The Config Model Publication Set message can be used to configure a model to periodically publish its status.
If a model doesn't support publishing the `publish_timeout_cb...
Hi,
I've added WFE\WFI to my application running on nRF52840 on my RTOS Idle Hook.
Runs fine when debugger is attached , but when debugger not attached - the application...
Hi
I have merged NUS client , NUS server and multilink examples.
It works well and no problem in functions.
Now i will make that the module(with multilink nus server...
Hi guys,
sorry but first of all I have to admit that the migration is a mess. And really do not understand why you entered nrfx and did not make a clear cut. Because saving...
Hi I want to get the peripheral address from the UART and compare with scanned peripheral addresses from the central (nrf52832) and if the received address string is of one...
I'm using a custom PCB with a Laird BL651, which contains a nRF52810.
I've been following the "Transferring Project to nRF52810" tutorial here to run one of the simple BLE...
Hi
This is in part related to my previous post on PWM signal generation on two channels that are 90 degree phase shifted. The frequency of the PWM signal generated was...
Hi,
I am using nrf51422 in my project.So we are using keil5 u vision project and sdk 12.3 version so here the problem is when i tried to open the blinky project it is showing...
