I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello,
I am trying to measure the current of the dk. I added the 10o resistor, loaded the ble blinky example and connected two probes. This is what i got:
In the idle...
Hi Nordic,
we started with the light_switch example
and created a second onoff model to it -> system compiles but runs into error
also tried adding a other generic model...
Hi All.
In custom report descriptor I try to use this code:
ret_code is NRF_SUCCESS
but on host while reading feature report I don't se a changed value. Maybe I'm...
Hi,
If an ESB PRX has queued a 250-byte auto-ack payload, that will take around 2ms at 1Mbs to transmit.
If the ESB PTX has the standard 250us repeat interval, will the...
I am confused about the value of RX_PW_Px register what will be the value of this register if more than 1 dynamic payload packet arrives on the same pipe-x.
I'm a beginner I'm having hard time understanding UART. In my opinion, the documentation is going too straight to the technical details and tutorials without even starting...
Dear friends,
Is there any ideas for measuring the distance between a BLE module and a beacon module without using RSSI?
With Regards,
Sunil
Calixto Systems
hi..........
i have developed nRF52832 QFAA using your schematics,and i have added sensor to it . Now i can able to flash the code and ran successful but i can't able to...
Hi,
We are developping a system connected to several devices based on NR52 MCU.
The DFU works with the nRF connect application.
Now, we would like to update the device...
Hi,
I am just getting started with the thingy 52 and I need some guidance. I am a EE by profession so I feel a bit out of my league here.
When I unwrapped my thingy I...
Hi there,
I am adding security to my service characteristic and i found that for security mode 1 level 4, bonding is required in order to access characteristic values. Is...
Hello,
My problem is pretty much identical to this one:
devzone.nordicsemi.com/.../
My functions look exactly like the ones posted in the original question and I...
Hello, and thanks for all the great examples!
I've gotten the COAP transport for background DFU working on my custom hardware platform and app, however I have noticed that...
Hi,
I do have a NRF51-DK and want to use it as a external programmer. I connected it to the OUTPUT Port which worked fine, then I flashed the mbed firmware on it because...
