I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello.
I wrote a simple beacon application which advertises with uuid, major, minor and name. Now what I saw in sample beacon I found somewhere is that nrf connect properly...
Hello!I am using NRF52832. The antenna is aca-5036-a2-cc-s produced by INPAQ, but the bluetooth cannot be found.Whether the adaptive antenna can be provided and the technical...
Hi Every one,
I am trying to use two uart's communications concurrently in nrf51422, in my code i am running timer of one second.
Every one second in timer routine trying...
hi....
i am using nrf52382 and segger 15.2 version , i want my peripheral to send the data only if it reaches the certain limit (threshold value) on that case it should...
hello , friends
i am using nrf52832 ,debugged the ble uart program ,and then i tried to connect my device over ble uart app,i couldn't found my device ,then i tried to connect...
Good morning!
First of all, the background. I made a custom board and programmed it, everything worked like a charm. After that, I made another one, same hardware, same...
In my previous question , where I wanted to atomically send a large bulk of data, the solution was to keep track of p_bus-> free_buffers , in order to calculate the amount...
Hi,
I’m using SDK 15.00 and I have some issues with NFC. When I’m trying to connect with NFC - NFC_T2T_EVENT_FIELD_ON event occurs. At this point, I need to start BLE...
The release notes for S132 v6.1.1 lists a bug fix:
"Fixed an issue where NRF_TIMER0 may not be reset at the start of a radio timeslot (DRGN-10650)."
Did this bug exist...
Hi,
Here and here are examples of a port of the nice u8glib library to stm32. Based on these, i tried a port to nrf52, but was not successful so far.
I call the oled...
I am trying to save data to the flash memory. My starting file is the ble_app_uart_pca10040 (s132). I am using the sd_flash_write address is 0x007ffd0 and a value of 0; I...
We have developed a custom board using Raytac MDBT50Q with NRF52840. It has an external EEPROM and a RTC. We made an app that we use to program 4 daily alarms through BLE...
nRF51822-EK page is no longer available on the website. By any change I can get the PCA10001 schematic somewhere?
I would like to run some conductive RF testing and would...
