I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
We are having problems with Gazell pairing. Both the host and the device are using the Gazell stack from the nRFgo SDK 2.3.0.10040 ported to run on an Atmel SAMD20J18...
sdk 15.0, SES
In CMSIS checked NRFX_TWI_ENABLED, and checked and unchecked TWI_ENABLED to no avail.
Looked at driver API , but with no specific hint.
Looked for other...
Hi Engineers !
We are going to implement AES CRYPT/DECRYPT Protocol over BLE to add some additional protection against HACKing with use of HW " 6.6 CRYPTOCELL" the MODULE...
Hi, I want to use a couple of 0805 resistors, hook them up in tandem to 220V AC power source, and then do some zero-crossing detection.
I know I know, this totally isn't...
Is it possible to use the Segger SystemView software with the NRF52832? When attempting to use SystemView, I get an error "RTT Control Block not found". It's possible to enter...
Hi,
I can't find information what shape of spectrum I should expect from test mode (CONT_WAVE = 1, PLL_LOCK = 1). At the moment I get main spike with smaller symmetrical...
I'm running into an issue when trying to use the timeslot API for advertising while concurrently scanning. Scanning is using a 100 ms interval with 50 ms window and initialized...
Hi!
I have created a project for nRF52 DK in Segger Embedded Stuido. I wanted to creat it for nRF51 but there was no eamples to start from in the sdk that supports pca10030...
I used the example ble_app_cts(SDK12.3),but when I connected the board(NRF52832) ,I did not find the cst service,Now,I want to know why I did not find the service and where...
Hi everyone.
I'm currently working with NRF SDK for Mesh v2.0.1, SDK v15
I'm adding light switch provisioner to light switch client example.
In file provisoner_helper...
I have to develop an appropriate driver circuit for a DC Motor, the Motor is to be connected to the IoT node Nordic Thingy 52, which can be switched on and off with the button...
Hi all, I'm developing a project based on nrf52832 and a custom board, what I want to know is if it's correct the actual power consumption.
The custom board has the following...
Hello, I am still using S132 version 2.0.0-7.alpha with Keil uVision V5.21.1.0
Should I move to newer version. Why uVision doesn't see new S132 versions in the pack installer...
hi hi hi everyone
i'm wondering can us use HCI protocol to develop our product without using by the softdevice as you know by using the softdevice we can just interact with...
