The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi, I use NUS quite alot with the following condition;
(SDK 7.2 & S110 7.1 with IAR 7.1)
When the peripheral only uses NUS, iOS cannot detect the peripheral at the ...
Naive follow up to What is NUS? .
Is NUS merely a vehicle for tutorials and fast prototyping? Or can it be used to build real world apps on?
If so, do we rename the...
Hi All,
We are in design phase of our project . We would like to use NRF52832 for our project.
Our project is a wearable based on BLE. We are planning to use RTOS in NRF52...
I am starting to port the example
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_peripheral\ble_app_hrs to my board. I haven't made any change to the example to save something...
Hello, I have a problem when I attempted to increase timeslot length with 10 ms ,every time I received NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_FAILED signal.
Why can't to extend...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE.
If the program is wrong,The chip will reset,
I want to save some data to the FLASH area before the chip reset.
What I need to...
nRF 8001: How to use it in Beacon mode where in no pairing or Bonding is required and
it only transmits some information which cn be received by any phone that comes in range...
Hi.I had been confused with parameters of sd_ble_gatts_characteristic_add( ).If I set parameters
like that:
static uint8_t ast_notify_char;
..........................
HI,
I have to implement buttonless bootloader.I am having simple doubt.I am programming softdevice,application(Hrs example with bootloader),bootloader hex file using nrfgostudio...
Hi,
I am trying to perform RF production testing using nRF51 development kit. My DUT is another nRF51 DK. I am setting my DUT according to Figure 2 mentioned in nAN 34...
HI,all
when i want to notify with MITM,there is an issue with my project.
my central role device is IPHONE and the app is lightblue .
When i enabel notify ,the nrf52382...
Hello,
I am using battery (3V) to supply nRF51822 system and the circuit is made according to DCDC mode circuit. My question is :
what is lowest voltage the battery can...
I have two p_storage_param modules param and param2 . param would store 3 blocks of 16 bytes and param2 would store 10240 bytes (10 pages). I called pstorage_register (param2...
