I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello,
How the modem selects it band of operation. Is it done automatically selected by the modem after registering to the base station? or is it assigned by the base station...
The modem firmware version 1.1.4 has been certified by Verizon, and the corresponding NCS version is v1.4.2. Now Nordic has released the NCS SDK version v1.5.0. This version...
To the kind attention of Nordic support team,
if it is not much trouble I would like to know what you consider a good/acceptable ble antenna efficiency in
desktop environment...
Hi,
I am using an nRF52832 with S132 and SDK v15.0.0 and already read in the forum about issues related to the SAADC calibration (inlcuing the erratum [86]). The problem...
Hi Nordic,
I have 2 charac i can write, let's name it A and B.
When i write into A, it trig ble_A_on_ble_evt , BLE_GATTS_EVT_WRITE , no problem.
But w hen i write...
I started developing a project on nRF52. My task is to read the value from the light sensor (phototransistor).
The sensor is connected in this way:
my code:
init...
when i Use 2.4G radio to communicate with other modules,like cc2510, i have many questins:
1. as we known that CC2510 ' modulation format of the radio signal ,MSK is only...
Hi,
Maybe this is obvious, but I couldn't find the answer anywhere online. When I power my dongle from an external 3V3 source, can I still plug it in to my computer and...
Hi, during my tests, I use an NRF52 Dongle with the nRF-Connect app as a USB/BLE interface, but now I need to handle some custom data. I have seen that the dongle uses a COM...
Hi!
I'm working on using the SAADC in 14-bit sampling mode (oversampling set to x2) using nRF SDK 17. The supply voltage for my chip is 3.3V, and I have the reference...
Hi @ all, can anyone here recommend me a suitable chip antenna, preferably one with matching regulatory documents in combination with a nRF52840 MCU.
Thanks and best regards...
I am trying to flash a NRF52832 using the J-link EDU mini in the Arduino IDE but I am having no luck.
I have successfully downloaded... 1. J-Link Software and documentation...
While digging for electrical information I came across :
.63ma using HFINT or 1.58ma using HFXO ?
So I hunted down HFXO to see how to switch between them:
But nothing...
please advice how to add "QDEC_NRFX" to the project configuration of 5340
1. it's not on the default menu config
2. I have tried adding under "ncs\v1.4.99-dev1\zephyr...
