I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi
This question is related to sd_ble_gap_keypress_notify() . According to Nordic softdevice S132 v3.0.0 API:-
"This function can only be used when an authentication...
Hi
I am currently working on calculating the AoA. I have 4 nRF52833 DKs and I am using three DKs as transmitters and one as the receiver and the receiver is connected to...
This page https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52840-DK/GetStarted says " If step 4) below fails, you need to re-program the factory example code...
How can I calculate max and average power of this chip? During use, I intend to be at 0dB TX and 1 Mbs data rate with a 3V supply. I am going to guess the max power draw will...
Hello everyone
I am using nRF52 DK PCA10040.
I try to generate puls by Timer 0.
The puls width is 400ns.
This goal was failed.
---------------------------------...
I'm struggling to get buttonless DFU to work with FreeRTOS. I've gotten buttonless DFU sample to run on the hardware. I also have FreeRTOS running on the hardware. However...
Hello,
I need to remap ble bootloader because I want to use nrf52832_AB instead of nrf52832_AA found in dev kits.
I wish I could have this memory mapping in embedded flash...
Viewers! Don't click on a similar issue or you will lose everything you have done!
Calling this method sd_ble_gatts_characteristic_add(...) with a characteristic value...
Dear all,
Im trying to interface LIS3DH with the following code, and drivers of LIS2DH (LIS3DH and LIS2DH have the almost same hardware and config.)
I have included...
It seems there is hardware support for NB2, but the modem firmware isn't there yet.
What's the timeline on this? And if a precise time isn't available, is it in the order...
Hi!
I know, that there are some similar issues in this forum, and I checked them, but I didn't see the clue.
I try to use fstorage to write something to flash. I have...
After many hours of successful LTE connections and using the AF_LTE socket just fine (many creates, many send/receive, many closes), my application now hangs on a call to...
Hi What is the ADC frequency range and operation at nRF52833 ? we are interfacing the TUSS4470 with nRF52833 ,WITH SPI communication . is that the frequency range supports...
In past I try to solve this problem:
https://devzone.nordicsemi.com/f/nordic-q-a/51249/state-chaneged-flags
Now I have new informations about this problem.
Using hardware...
