I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
According to the Online Power Profiler , the Standby time between Crystal start-up and Start radio is ~1 ms; however, we measure a variable amount of time between 0 s and...
HI All,
i m new to this technologies.Now m using NRF52840 DK and sdk as nrf15.2..we have developing the nrf52840 as a beacon scanner to scan the ibeacon details like rssi...
I'm using a Nordic dev board (PCA10040, nRF52832) with modified "Nordic_HRM" firmware sending packets of 20bytes at 100Hz over Bluetooth Low Energy.
I'm using Nordic's heart_rate_collector...
Hello everyone! I have followed the tutorial " Installing a 6LoWPAN enabled Linux kernel and required modules" and i have compiled the UDP client IoT example in order to test...
Hi everyone,
I am using nRF52 which has 52832 on it. Currently, I am working on 2 nRFs and one RPi with MQTT on the softdevice 132. One nRF is the publisher, another one...
I am using pcaboard10028 ,sdk12.3.0 and softdevice s130. I am using proximity example to read battery percentage level,so giving adc input as following:
channel.config.config...
Hi, I'm having problem with UART communication. I use basic UARTE code and I want to send simple data to PuTTy terminal. The problem is whatever I would send i get only 'K...
Hello!
I'm trying to update the bootloader of a nRF52 device OTA. We are using SDK 12.3. The device has our own application flashed, along with what is essentially the bootloader...
Hi Sir,
We want to know about AoA /AoD applications for 52811, and there are some question as below.
1. Is there a difference between BT 5.1 and BT 5.0 from the perspective...
Hi,
I'm implementing quadrature encoder to read motor speed/position. So far I configured a gpio pin where A channel of the quadrature encoder is connected to capture timer...
Hi, I'm now using nRF52DK with Keil and have followed the getting start manual in the Nordic Devzon.
Till now, I completed UART example and want to add ADC function to this...
Hi,
I wanted to know what is the recommended way of data transfer through ble if there are multiple sensors. Is Creating one service with multiple characteristics a good...
Hi everyone,
I am using SDK 15.2 with keil microvision and softdevice132 nrf52_6.1.
In version 13, system dispatch event was regestired with Softdevice handler as below...
