I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi, in my project, the following codes caused "NRF_BREAKPOINT_COND":
sd_power_ram_power_set(4,(POWER_RAM_POWER_S0POWER_On << POWER_RAM_POWER_S0POWER_Pos) | (POWER_RAM_POWER_S1POWER_On...
I have secure DFU working fine for my s132 (SES sdk15.0), and now trying s112 using the example from post how to use dfu?
I used SDK_14.2.0_nRF52810_Secure_BL_v1.1.zip and...
Hi. I have to make mesuring impulses quantity of two external low freq signals without interrupts.
I tried to use GPIOTE EVENTS_IN[0] and 1 with PPI ch 0 and 1 to timer...
I use PCA10040 V0.9.0 to run SDK15 bootloader example: F:\Nordic\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10040_ble_debug\arm5_no_packs.
1. erase full chip...
Hi, I am using the ble_app_cscs_pca10056_s140 example application from nRF5_SDK_15.0.0_a53641a and I have made a single-line change (see below) to force the bonding process...
Hi Nordic Team!
I have bought nRF52 DK and my aim is to create BLE application for a peripheral that it would be possible to connect multiple centrals (for example android...
Hi,
I am trying to add the SAADC to an existing project. SDK 14.2 - Softdevice.
I quickly changed the existing code as follows:
Unfortunately, the callback gets...
Hi.
I am using the nRF52840 DK board and have integrated the SDK15 ESB_Rx example with the HID example.
The nRF52840 DK board has two USB ports. (J2, J3)
J2: Firmware...
Trying to track down an issue with IOS disconnecting shortly after connection when using NRF Connect, LightBlue doesn't connect at all.
We have a few GATT chars with...
Hello,
I am facing an issue when trying to use the example flash_fstorage_example in SDK15 with the softdevice. According to the documentation, using the reading and write...
I am testing SPIS to transmit mass of data(255 bytes each call) from nrf5 DK.
I found SPIS data shifting randomly.
The testing data is 0x88 but sometimes can get 0x44...
Datasheet of the Sensor:
www.ctconline.com/.../1_VS_TA102_DS.pdf
Accelerometer Out = 100mV/g =equivalent to=> +/- 8Vpk-pk
Temperature Out = 10mV/°C
Please provide...
FDS uses softdevice API. SDK 14.0.0
FDS writes are all successful for the same file id and different record keys until the flash is full
fds_delete_record() is called...
Hi,
I'm developing software for the nrf52832. However, I can't use the SDK of Nordic for several reasons.
In the code, I would like to save a small amount of data...
