After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
I was actually trying out Nordic mesh topology and wanted to tryout the example programs.
SDK: nRF5_SDK_15.0.0_a53641a
mesh: nrf5_SDK_for_Mesh_v2.2.0_src
IDE:...
Hi Everyone
I am using
SDK 15.0
Segger Embedded Studio
nrf52840 on a custom PCB.
Softdevice s140.
FreeRTOS.
My requirement is , on the press of a button , the...
In the news today (26 Oct 2018):
http://www.eenewsembedded.com/news/embedded-studio-410-arm?news_id=111432
Will this work with current Nordic SDKs, or should we wait...
I am using FreeRTOS (sdk 15.2) configured to use RTC for the tick source and systick timer for the system. I am trying to put the device in a low power mode. I have tried...
Hi,
I use Iphone to scan for arround ble package.
The beacon is configured broadcasting every 200ms (I think all 3 channels 37, 38, 39 is default to broadcast signal in...
Hello,
I have a secure bootloader and an application on nRF52840 with SD 15.2.
I try to add watchdog support in application based on watchdog exemple but if i remove feed...
Hi,
i'm actually working for interface the nRF52 with the STM32. Actually i completed the part where the STM32 send some data and the nRF52 recive it.
Now i need to do...
Hello,
I am a beginner with Nordic semiconductor. I downloaded SDK v15.0.0 and used some of the examples and it worked perfectly for me.
My project uses different modules...
Wiring diagram
Testing process，The product will automatically disconnect. But it can connect again.
After setting the voltage to 1.8V in the voltage Reguator,...
This time I am trying to run Wireless UART Example but it seems that it does not work.
After I flashed dev board no LED were turned ON or flashing but web site says:
LED...
Hi!
Is there an example to extend the Bluetooth MTU size to more than 20 bytes together with SDK 15.2?
I found only examples with older versions.
Thank you in advance...
Hello
I'm wondering if it is possible to upgrade over-the-air from SDK11 to SDK15.
I know already that using the example bootloader from SDK11 will not work because the...
Setup: nRF5_SDK_15.2.0_9412b96 / s132_nrf52_6.1.0_softdevice / nrf52832
I tried to make a multilink nus central (PCA10040) with 2 peripherals (PCA10028) connected to it...
Hi, I would like to send data from nRF52840 Dongle to Raspberry Pi 3 through USB-UART. I programmed the ble_app_uart_c example found in SDK 15.2 and I connected that to my...
