Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Figure 222 of the OP spec states "important: no components in bottom layer". Are you recommending that we keep the bottom side clear under/near the nRF52840? This feels a...
I met some problems in testing ECDH , the project is the example in E:\Source\NRF52832\nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
Hi!
I am using SEGGER Embedded Studio for some of the projects. I do utilize C++ in the projects wherever possible and have found that I cannot make the delete operator...
I am working with nRF24LE1 and I use the Gazzell library. But I need a real time base. I have a chance, because I think Gazzell uses that resource. Is there any way I can...
Hello
I am using gazell on the nRF24LE1.
I would like to know some recommendations on how to estimate a consumption on the side of the device based on the times and repetitions...
Hi. I just recently started using nRF24L01+. I am trying to simulate MultiCeiver using 2 mcus and 2 nrfs.
PTX sends a message on all 6 pipes of the PRX. The problems start...
HI,
I look at nRF5 SDK doc about Gazell,see that 'the nrf_gzll_device_tx_info_t contains the num_channel_switches parameter which can be used by application to determine...
Hello
I am quite a beginner and have been trying to get it work for 2 weeks now.
I would like to merge these 2 example codes from nordic:
Shockburst TX example...
Hi everyone,
I want to use MasterEmulator.dll (2.1.13.14) in my own application (C#) for development. Then I realised that line
MasterEmulator mMasterEmulator = new...
I am using nRF52 and Raspberry Pi 3 (with BLE).
In the Raspberry Pi, I am using bluez.
I was attempting to connect with the NORDIC_BLINKY app but the message below was...
Hi, I wonder how to get the Nordic SDK-examples work with VisualGDB.
As I would like to read TWI sensor values a good point to start from are the Nordic examples.
But...
my project is used nrf51822 mcu, it contains SIM, when the mcu is reading SIM data, and at the same, I take out theSIM, and the 51822's pin which is link with SIM is can't...
