Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
We have an use case that we may need to support up to ,say 500 sensor nodes and it may be added or removed dynamically. And we should collect all sensor data within 3 seconds...
Hi all:
Based the descriptions in data sheet, the GPIO9 and 10 are set to NFC antenna pins by default.
And I cannot control these 2 pin correctly by configuring the pins...
I want to use NRF51822 to advertise is door close/open. No need bidirectional data sending.
Only one way from NRF sensor to mobile phone app.
Actually I have only two different...
I am using NRF52 S132, and using UART service , but my phone is getting disconnected automatically after 1 or two minutes. I have seen this question asked in Forum but that...
Hi,
Has anyone test with Nexus 5X ?
I could not change connection interval 7.5ms, the interval is always 45ms.
Does anyone know how to change the connection interval...
SDK 9.0, examples/ble_peripheral/ble_app_hrs
Trying to use DFU with a bond device, I got aware, that after the update, some "static" data seems to get corrupted during...
In the Keil Pack nRF_Libraries V3.10 [SDK V10.0.0?] (Low-Power PWM Example)
Not a big Bug, but an inconvenience all the same.
low_power_pwm.c line 165
ret_code_t...
Hello,
I want to change the advertising timout during runtime. We have two use cases for our device:
Batterie mode --> advertising timeout = 2min
Power...
Hello,
Implementing a LED led driver was pretty simple and below code works well:
nrf_gpio_cfg_output(LED_PIN);
nrf_gpio_pin_clear(LED_PIN);
NRF_GPIOTE->POWER =...
Hi there,I am using the PWM library in github github.com/.../nrf51-pwm-library . After I do this in my project and I check the pin output with Oscilloscope but didn't see...
I have a product that was released a few months ago and is operating in-the-field. Recently we discovered a bug and need to fix it. We are unable to do a DFU because:
...
Hello,
DEVICE_MANAGER_APP_CONTEXT_SIZE should be less than 256 bytes in size.
However, it seems to work properly (not fully tested) whith a size of 800 bytes, and no more...
Hi all,
I want to make sampling from microphone at 16KHz. So I want to first disable softdevice, do all measurements. An after that enable softdevice to transmit data. Will...
Hi,
Recently, I am playing around with the NRF51 dongle and trying to make it work as a BLE master.
However, when I run the sample code(e.g. advertising, multi-link .etc...
