Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
I'm performing power measurements with nrf9160-DK running the Serial LTE Modem application.
The example SLM has been modified to add support for HTTP, MQTT and also to relocate...
I have been following the NCS BLE tutorial part 1: Custom Service in Peripheral role - Getting Started - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com) for BLE and...
Hello,
I use nrf52832 and SDK 17.0.2.
I use flash crashlog to store crash log on the flash.
I enabled NRF_LOG_BACKEND_FLASH_START_PAGE = 0, which means flash log area...
Hello,
I have a problem with the GPS and more precisely the AGPS. I would like to retrieve my position with the thingy91, I created a project by taking the AGPS sample and...
So, for a while I have tried to follow these instructions: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_doc_user_guide_modules_dfu_configuring_performing...
Hello,
Developing on Zephyr 1.2 and modem fw 1.2.
Developing a client LTE application. If I run the below sequence of commands periodically every 2 min:
eventually...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr.
In this process, I am trying to connect with the sensor API with a "fake" sensor whose...
I'm not certain where to send suggestions, so hopefully this will do...
A very useful addition to the nRF Connect SDK would be support package documentation for Zephyr...
Hi,
I am trying to run the NCS Zephyr ADXL372 sensor sample application (using nRF5340 DK) but get the following error:
This corresponds to the following NACK error: ...
I would like to do mutal TLS on a NRF9160. I found the https sample where the firmware does server authentication. How do I add client side authentication to this example...
I have a project from 3 years ago (2018) that I'm trying to make a simple update to the application code. The code downloads via the Segger Embedded Studio and runs correctly...
A vulnerabilitiy in BLE secure connections is reported as CVE-2020-26558 : Impersonation in the Passkey entry protocol
"The Bluetooth SIG is recommending that potentially...
My application uses a NRF52840 (SD140, SDK 15.2.), very simple circuit and needs to be extremely low current consumption. I measured the current in conditions of BLE on and...
I'm trying to get a BLE example for NordicSemi nRF52833_xxAA using SoftDevice S113.
I found out only two examples but they don't compile.
Error[Go029]: Variable "sec_mode...
Hello,
Is it possible to disable the antenna pin of the NRF52 in software? I cannot see anything in the data sheet which suggests this.
We are using a third party module...
