Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
I am doing OOB commissioning with OpenThread. According to section 10.12 of Thread 1.1.1 specification, Active / Pending Operational Datasets need to be persisted to...
Hello,
I'm trying to connect external RTC, which has a 32kHz clock on it's pin to nRF52832. So far I've had issues with connecting this clock to P0.00 pin and having P0...
Hi all:
when i add uart code in ble_multilink ,and it gived me errors like this:
"<error> app: Fatal error <warning> app: System reset <error> app: Fatal error <warning...
If I put too many characters into a serial using IRQ mode, it stops reading input.
I haven't tried polling or DMA yet.
Using
nRF5_SDK_15.0.0_a53641a
gcc-arm-none...
Hi ,
can u please provide more details about error code 4, returned by ble_ancs_c_init function.
what is this error, and how to resolve it???
thanks,
amarjeet
Hi there,
we are developing an application based on simple IEEE 802.15.4 packets, for which we use the radio peripheral. Every example found in the SDK starts with switching...
Hi
I would like to perform a connection over 2MPHY instead of 1MPHY; is there an example to show this? This should be doable according to the softdevice v6.1.0 changelog...
Dear Nordic
I am doing a project that has a multilink one central and ten peripherals.
So I started with ble multilink multi role in here . I added ble_nus_c and uart...
Hello everyone,
I am developing a ble device and cant get under 7mA.
For test i used example application. BLE Beacon example. And the hardware part is realy basic. Only...
Hi,
We need to design a network with one master and 36 devices connected, with "long range" capability, exchanging sometime messages from 100 to 4000 bytes.
The number...
I understand from forum post https://devzone.nordicsemi.com/f/nordic-q-a/19250/the-number-of-central-connections-in-s140 that S140 v5.0.0 1.alpha release supports 8 concurrent...
I understand that Nordic provides a proprietary DFU via the BLE mesh. What mechanisms are in place to ensure that all packets reach their destination, e.g. acknowledgements...
-Using SoftDevice S110 8.0.0 for the nRF51822_xxAA.
-UART0 running on 19k2 without flow control (only rx/tx) and using irq priority APP_IRQ_PRIORITY_LOW (=3)
-Using the...
I'm currently porting my code from nrf52832/S132 to nrf52810/S112 (SDK14.2).
It seems that the s112 has no support for scanning, i.e., BLE_GAP_EVT_ADV_REPORT, sd_ble_gap_scan_start...
