we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
I have got two questions:
1) I am trying to write a code into nrf52840, and was wondering is there a specific SDK version to be used for the nrf52840 DK, or we can...
Hi,
I have used Nordik UART iPhone App code for our App development
Now till iPhone 7 App is working fine.
Now when I run App on iPhone X it is displaying log error...
I have a usb dongle with nRF51422 (PCA10031) and downloaded nrf sniffer software version 2-beta from https://www.nordicsemi.com/eng/nordic/download_resource/65225/1/90637756...
hi,
i am using NRF52832 DK, and sdk 15.0.0.0 ,,
i want make the central to work also as a peripheral...i.e whenever central is not working ,or ,central is not in connection...
I am evaluating the throughput of BLE communication between 2 NRF52832's, 1 acting as a central and 1 as a peripheral. I've modified the ATT_MTU Throughput Example, and I...
Gone through sdk 11.0.0 Experimental_ble_blinky application, i trying to assign one gpio pin in place of connected LED. what is it receiving when pressing on & off switch...
Hi,
I'm working with nRF52832 chip following the example "ble_app_beacon". I see the advertising packet is limited to 31 bytes only. However, I'd like to take an advantage...
Hi,
I have arm based application processor and need to connect with nRF52840 using UART, I don't have any idea about bootloader and factory firmware when hardware assemble...
We are trying to determine the emission designator for the nRF52832, or at least to determine the necessary bandwidth so that we can create the emissions designator. Please...
Hi everyone,
I have a problem with SOME android devices.
In particular Android devices with BLE 4.0 & 4.1, but I have NO problem with Android device with BLE 4.2 and iOS...
Hello,
We are using nRF52832 DK with SES IDE and latest SDK 15.0 sd 132. We have developed one multiplink central device and modified ble_nus_c with our application to connect...
I use nRF52832,is 2.5v power supply,but you can't download the program,w hen I set the voltage above 2.8v, I can download the program,then I switched the voltage to 2.5v and...
Hi everyone
I am able to send the data over the UART to the Real Terminal and also to my other device working on UART protocol. However , I am not able to read the data...
Hi,
I am willing to migrate sdk 14.2 code to sdk 15.0 code. Do you mind me to ask a crypto micro-ecc question, please? Thanks.
In sdk 14.2, the micro-ecc part definition...
Hi,
I am working on nRF52832 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
When I am trying to initialize a structure in Flash memory, the...
