Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I am running the nRF51822 from a coin-cell. I need to measure the cell voltage. Until now, I have attached VDD to an ADC pin with a voltage divider and a capacitor...
Hello~
In my production line use jig contact my PCBA, and use Jlink connect to Nordic 51822 download FW, but I found sometime can use 500kHz and sometime can't use, just...
Hi
I am using nRF52(PCA10040) as a sniffer dongle, but it seems the sniffer mode cannot work, and shows the error log: "INFO: Error on port xx. file: Packet.py, line 245...
First step of trying to integrate S132 to a small OS is failing completely.
When I use SVC the system ends up in hanging in hard fault.
The SoD handler ends up trying...
I am testing to develop an application that sleep (system-on mode) for most of the time, and it wake-up periodically to send out somethings.
As I would like to lower the...
Hello,
After when I download the protocol stack（S132）.The target is NRF52832 chip，tool is J-link OB.
I choose to recover nrf52 ，then prompt unable to fine or open the...
Hi,
In ADC, we would be using the internal voltage generator as the reference voltage. How stable is the voltage coming out of the reference generator. Would it be always...
It appears that, if I wanted to write characteristics to my BLE device, I can utilize the writeCharacteristic method of the BluetoothGatt class. Is this the right way to go...
Hello,
I am currently for a quick solution to test NRF24LE1 compliance to FCC. Can you provide me with any code if possible? As i could see from the website only an application...
Hi,
We can utilize the 31 bytes of advertising packet as well as 31 bytes of scan response packet which in total makes it 62 bytes of advertising data. What is the effect...
Hi dear Nordic Engineers.
We going to move from FN-LINK (Realtek) I.C. BLE to nRF52.
FN-LINK uses HCI (UART) BLE the Interface to communicate with our embd. LINUX.
How...
Hi all,
I'm using pca10040 board with sdk version nRF5_SDK_11.0.0-2.alpha_bc3f6a0.
There i'm using example code of spi handling. Instead of nrf_log_printf i changed...
Hello,
There's any known issue realated with DFU and Android 7.0? When we try to update firmware with nRF Connect or our APP we get an error (hex file error), but when...
I am going to develop an application on nfr51422 that requires very low current consumption. Basically we plan to make the nfr51 to "sleep", and it will wake up constantly...
