I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I'm searching a way to create a function which would be a timer function (so, this function will have an int number as input parameter), and during this delay, I would...
On this question I read that S110 is blocking CPU a lot during advertising/connection ( devzone.nordicsemi.com/.../).
On this other question they say that you can change...
I am using two nrf51822 ek. one is programmed with multilink central and other is programmed with multilink peripheral. when i press the button on multilink peripheral, i...
I need to connect to a beacon with a scanner nRF51 using the advertising data of the beacon. Then i need to get the service and characteristics of the beacon.
Thanks
Hello everyone,
i am trying to compile the Ble-UART_example but everytime it shows this error 'GPIOTE_config_irq_priority is undefined ) and i dont know what went wrong...
I have tried to flash my application targeting nRF51822 on our board by using a Segger on nRF51 DK. However, Keil compiler always shows that it couldn't find any nRF51822...
Hi NORDIC
I have to complete a function that one can transmit and the other can receive . but I do not know how to set nrf51822 to be a receiver . please tell me or share...
Hi,
it seems that the default implementation of the ble_bas (battery service) provides the notification feature but not the "read" feature.
I client can enable notification...
I'm using the Github project github.com/.../nRF51-multi-role-conn-observer-advertiser in order to SCAN in a specific channel rather than all 3 channels. In this example, softdevice_handler...
Dear all,
Recently,i use nrf51422 trying to receive data from two ant sensor.
i assign two ant rx channels at the same time, i find i can't receive data if only one sensor...
We are planning to use a synchronous independent channel, that senses whether there are any slaves or not using acknowledged data type.
More than one slave could have paired...
HI,everyone!
I want to use pstorage to store some data, so I followed the steps given by devzone.nordicsemi.com/.../ , but it didn't work.
Then I checked ecah function...
Hi all,
I want to test power consumption of data packets reading from SPI to RAM using PPI.
But i'm not sure that can RAM act as a peripheral of PPI...
So, can i use...
I am using a solar powered energy harvested circuit to power the nrf51 module. However, when the generated voltage drops below 1.8v, the nrf51422 enters into brown out reset...
