Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Posting this as separate question as it got no traction in the other thread:
Why are there many of the same include files in the DFU example directory as in the S110 7...
Hello:
After the nrf52 lost connection with the phone, should it go to the Directed mode of just start normal fast advertising. And what the differences between them?
...
Hi,
I just used the nRF Connect Toolchain manager to install the NRF Connect SDK. Then, the Segger studio keeps popping this error when I try to open a project:
And...
Hello,
From the nrf91dk datasheet, a stackup is provided. Because it looks custom, and I'm having a hard time finding a manufacturer that can do that stackup. What PCB...
hi，
I read the data manual of 52832, but I have some questions about the following parameters, like CM_FLASH,CM_FLASH/MHZ,CM_FLASH/MA,please explain it in detail and what...
Hello ervery one,
I am doing development on NRF52840. I have a problem as follows looking forward to your guidance.
I need to jump to Application 2 (address: 0x32000)...
I See in the discussion that I can see I/Q for AoA.
I see this examples "direction_finding_connectionless_rx" on zephyr I Think that I can start debug using the data from...
I want to transfer a few bytes of data between two NRF52 modules.
I have checked out the BLE Blinky and NUS example and understand the gatt client and server ideas.
My...
Hello.
I am using SDK version 17.0.2.
The example code uses nrfx_spim . Target board nrf52832
The nrfx_spim project confirmed that 10040 did not exist, only 10056...
hello,
in the case
Case ID: 227777
https://devzone.nordicsemi.com/f/nordic-q-a/46439/turning-services-like-hid-on-off-without-disconnect/309149#309149
In the...
I've got a Thingy:91 plugged into my computer and can see its USB terminals (/dev/tty.usbmodem143101 and /dev/tty.usbmodem143104). I can also see the "ZEPHYR USB" volume and...
Good morning,
I am working on nRF52840 DK, using nRF5 SDK.
I am trying to communicate using SPI.
However, I found out that the function nrf_drv_spi_transfer took 10µs...
I am developing a solution with the nrf9160 that should use LTE and GPS at the same time. But unfortunately I am having some problems. Perhaps somebody from Nordic or the...
Hi everyone,
I am working on a project using nRF905 as an emitter and another Receiver(different than nRF905), the receiver is programmed in a way to perform some actions...
Hello Nordic Team,
I am having issues with the peripheral_uart firmware for the nRF52833.
1.I can use UART_init() or nrf_drv_uart_uninit() in nRF52-SDK to enable or...
