Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hello!
I have a question about the slave latency: I know how it should work, I would like to know if it is normal that there are current peaks in the supply current when...
Hi,
Does anyone have a hex code that can be added to the app hex in order to get rbp for NRF52832? Or a code that can be used from Arduino IDE?
I know that it can be...
Following error throwing while using nrf tools
nrfjprog verion 9.3.1 -------------------------------------------------------------------------------- FUNCTION: open_dll...
Can someone explain the indepth working of nrf dfu bootloader example with respect to the init packet.
How is it decoded and the information gets stored in the structure...
Hello,
I'm getting started using the nRF Sniffer with PCA10040 and Wireshark on MacOS. I followed the instructions in the User Guide and was finally able to set it up by...
Hi
This is just a head's up. In function nrf_esb_pop_tx(void) you have the following code ...
Instead it should be the following...
Otherwise the bug is such that...
The Introduction page is inconsistent:
infocenter.nordicsemi.com/index.jsp
first it says
[quote]]The mesh stack is also compatible with the nRF52810 platform, but not...
Hi all,
As I've been researching, the mesh sdk is not supported on the nRF52810 SoC, although being compatible. Is there any development or plan in changing this? I'm planning...
Hi,
Is there any way to add conditional compilation in linker file?
I have two versions of a code, one with DFU and one without, i want to combine the versions. is there...
Hi everyone,
I used SPI interface to access a external flash with page size 256 bytes.
I found I can't access full page, because the maximum of one SPI transaction is...
hello all ,
controller nrf51822
i am trying to development for EPD 7.5 spi interfacing through external flash image send so how to set spi latch reset turn on parameter...
Hi, there
I try to use the nrf_atfifo in my program, but I found the atfifo cause hard fault in my program,below is how I use the at_fifo in my program.
and I also found...
Hello, I have a problem with my nrf52832 customised board
It has loaded the ble_app_uart example of the 15.2_SDK and It have the correct pinout from my board, These are...
1. I try DFU bootloader with OTA, it success.
2. But the Application was gone.
3. If item 2 is real, is that I have to porting the force enter to bootloader mode by botton...
