I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi,
I'm using sdk 15.2, with soft device s140 on nrf52840 dongle in peripheral mode. I'm using modiffied ble_app_proximity example. What I wan't to achieve is to set advertising...
I want SoftDevice of Bluetooth 4.2 for nrf52832.
I found softdevice.
15.2.0 nRF5 SDK
15.1.0 nRF5 SDK
15.0.0 nRF5 SDK
14.2.0 nRF5 SDK
etc
Which is Bluetooth 4...
i have one huge process one get positon sensor using i2c bus and another get led color also using i2c bus.
when color function is added in the process,positon sensor data...
Dear all,
I defined "DEBUG" , used UART peripheral and "printf()" in the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. I find nRF52832 always dead in the place at...
Hello,
To determine the current network topology I hoped I could use the heartbeats to determine the RSSI and the number of hops. The RSSI of the last node is in the example...
Hi,
I found this example here for nrf51.
github.com/.../nrf51-ble-gzll-device-uart
And this is more or less what I would need for my application.
Is there a way that...
Hi All,
Scanning with a nRF52840 Dongle, Is there a way to know if one of the scanned devices is using Coded PHY modulation to advertise? And if the answer is negative,...
OS ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board CPU :(Nordic) nRF52832 / ARM Cortex -M4F 32 bit processor 28-pin Land Grid Array / 15GPIOs / SWD Soft Ver:nRF5_SDK_15...
Hi,
I am using "ble_app_uart" code and added battery service to it as custom changes.
I want to update battery level at every 3 seconds.
Code is working fine and starts...
Hi - In the examples provided, a peripheral will go to power off after completing its transactions.This means the the application does not have to "clean up" afterwards. ...
in pca10056.h, there are 4 buttons.
I want to add one new button, //#define BUTTON_5 NRF_GPIO_PIN_MAP(1,06).
However , it failed.
I debug and find the issue, #define...
i used SDK9.0.0 to implement the function that bond to cellphone.
case 1:when i set the IO_CAPABILITIES to BLE_GAP_IO_CAPS_DISPLAY_ONLY,the process of bond is ble device...
Hello,
i m using sdk15.2.0 in nrf52840.
please help for increase adv data size from 31 byte to 45 to 50 bytes..
i had tried with "BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
