Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
We are using nPM1100 along with a STM CPU. When we put the CPU into deep sleep, it takes one minute for the current to go down to 20uA from 500uA.
We were expecting the...
I have a customised bootloader using uart + BL, built from the SDK examples and modified using articles found here. It works - most of the time. The product is a cusom board...
Hi to all,
this is my first public ticket ;)
I would power a nRF52840 on my custom board both with a cell battery (specifically CR2032) and the VBUS provided by the USB...
Hi, 1. After executing nrfjprog --recover command with PCA10040 DK, I read this hex: nRF52832.hex with Programmer
2. What does this program do that causes read protection...
I have successfully implemented an interrupt-driven method to read data from the MPU6050 sensor on the NRF52840, and it functions as expected. However, I encounter an issue...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
Is there a solution from Nordic available where I can have a LTE-M (or NB-IoT) and at the same time still receive the 1PPS output from the GPS module? It seems to be that...
Hi,
I am working with nrf5340 chip and I want to migrate from NCS 2.6.1 to NCS 2.7.0. I want therefore to apply recommendations: migrate to sysbuild.
With NCS 2.6.1 I...
I have an array of LEDs on my custom board. One of the LEDs is set on a UART0 RTS pin, which is GPIO(0,5), and we are using ground as common. To avoid any conflicts, I disabled...
My device is an nRF52840 running a C Code application that is built on nRF5_SDK_17.1.0 I am implementing a FOTA solution where a hex file fw image and a .dat file will be...
I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...
I'm using a thingy53 on ncs v2.7.0. I turned on CONFIG_ASSERT to try and find issues. This issue pops up randomly, it asserts the program crashes and causes me to have to...
Hello,
I am experiencing difficulties connecting my NRF52840 board to the nRF Connect software. Despite multiple attempts, the board does not appear to be recognized by...
Hi, I'm looking for the public mac address for nrf52840, and i find out that the mac address is located inside the register FICR->DEVICEADDR[0] and DEVICEADDR[1].
DEVICEADDR...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...