Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
I'm using SDK 2.1.0 for this project.
I found that when I shut down using the following:
pm_state_force ( 0u , &( struct pm_state_info){PM_STATE_SOFT_OFF, 0 ,...
Hello,
I’m trying to get an nRF21540 FEM working with a chip-down nRF5340 design under NCS v2.4.2. I’m able to enable the FEM at its default gain setting, but I hit a wall...
For a device like the nRF9160 Feather, you need a second USB to UART device for listening to the modem traces. When I go to select the Terminal Serial Port under Advanced...
I was trying to set up partitions on a nRF5340 DK so I can use MCUBoot, settings, and littlefs but am getting this error when flashing the dk:
The output Zephyr.dts has...
Dear Support,
I encounted an issue when tried to connect with complicated wifi network recently.
The error info is as follwing.
"WPA: 4-Way Handshake failed - pre-shared...
Hi,
we use our code for beacons for very long time now. Unfortunately producer changed chip.
We were using NRF51802QF with SoftDeviceS130.
Now the chip is NRF52810QCAA...
I am receiving the following errors: [00:00:00.117,187] <wrn> bt_hci_core: opcode 0x2027 status 0x12 [00:00:00.118,133] <err> bt_id: Failed to add IRK to controller Which...
Hi,
I am new to board programming. I have a custom board with nRF52881. There is no USB port on the board to connect it directly to the PC. How can I connect the board...
Hi,
I see in the GNSS documentation for the nRF52840 that the GNSS modem performs scheduled downloads in Periodic Navigation mode, and from some testing, I found the download...
I am using nRF52832 Board for DFU. I want to implement static partition required for dfu operation. I would like to know that where shall I save the pm_static.yml file and...
The ActiveHardwareFaultsEnum supports a "TamperDetected" hardware fault, which is of interest for our product.
Using the general diagnostics server, it is possible to set...
If I use zb_zdo_mgmt_lqi_req() for dst_addr = local short address is the response resolved internally?
I have an application where I need to locate certain zigbee devices...
Dear Nordic support team,
We are using the SDK v2.6.1 to build targets for nRF52840 chips, and are using multiple configurations defined in a CMakePreset.json file.
It...