Hi,
i want to build a BLE mesh via advertising. i asked some questions before about ibeacon and observer, how ever to clarify my question i have some additional questions...
Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
After preforming a DFU with the nrf connect app (ios) the device advertises and will "connect" with the nrf connect app, but its not actually connected which is evidence by...
Hi, I have a project that is comunication between nRF and Smartphone via BLE and using libuartes to comunicate with 2 another devices via 2Uarts. Now I need to combine 2 examples...
I have an BLE peripheral application running on a nrf52833 with softdevice S140 were I transmit data from Bluetooth to an external CAN-controller via SPIM and back. This is...
Hi, I want to enter the DFU by setting the register.But when the sd_power_gpregret_clr and sd_power_gpregret_set are set to set the register, and the err_code is 0x02 is returned...
HI
dk:PCA10090 0.8.5
modem: mfw_nrf9160_1.2.3.zip（ This DK board supports modems up to this version ）
ncs v1.9.0
example :serial_lte_modem
The NB card has been...
I added DCDC-enable to ble_app_beacon and measured the current consumption. As shown in the figure, spike current is generated during advertisement transmission. what is the...
Greetings,
I am running the "ble_app_template" example on my custom board using SDK v17.1.0. I am trying to figure out how to wake up the MCU from the SystemOFF sleep...
I currently am working on a BLE device in which I am trying to set the Service and Characteristic UUIDs. Here is an example of what I mean:
As can be seen here, the Service...
Hi there,
I'm in the midst of migrating between SDK14.2->15.2, and SD 5.1->6.1
I'm calling sd_flash_write() and sd_flash_page_erase() before enabling the SoftDevice with...
Hi,
I start a new design using the nRF Connect Sdk instead of the nRF5 Mesh Sdk.
Is it possible to provision a device over the mesh network using the NCS (like the PB...
After LPN publishes message, NRF_MESH_EVT_LPN_FRIEND_POLL_COMPLETE event is generated five times. Also I noticed that instead of transmitting single publication message LPN...
Hi,
We have a problem with a nrf9160 connected in NB-IOT with a bad signal.
During the debugging session to try to figure out what happen, we saw that the mqtt_evt_handler...
Hi everyone,
I have a problem since a couple of day with an interrupt of app_timer not triggering when adding a BLE central to my project. The device is working well as...
If I can get time through WiFi then send it to the nRF5340 and place it in a Struct TM. is there any method to have the nRF5340 maintain the time/calendar from that initial...
