Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
I would like to enable the APPROTECT readback protection.
What is the advised way to do this when using nrf connect/zephyr? The following line doesn't work (the 'at...
Hi everyone, I'm new to DevZone.
I am writing to ask for info for the first application with BLE.
I need to send data acquired by sensors, RAW mode, via the BLE application...
As far as I know "nRF Connect" DFU function just upgrade one by one,it's too low.
If there is no way to update in batches with DFU,who know a example that DFU function Host...
Hi Devzone:
I would like to shrink heap and stack size to save some RAM space.
I can see in the memory usage page of currently allocated heap and stack:
As you can...
Hello,
I have reserved an area in my flash mapping for settings (0x2000 length). I would like to update it (without application) with DFU / secured bootloader / nRF toolbox...
There is no 'low BLE power' example in the nRFConnect SDK for the nRF5340 - so I am just 'trying thinks' based on documentation I can find to come up with Application/BLE...
Hi.
I want to configure a scene when I create it on a node. So I need to use the Extension field sets, described in the ZCL 3.7.2.4.2.1. I see that the stack has a macro...
Hi Nordic Support Team,
My current setup is : Android Phone <--BLE--> nRF52840 <--LIBUARTE--> External STM32 MCU
I started the example with this folder in the link provided...
The following program will start the TIMER, read the timer value by pressing the button, and set the interrupt event. However, when the interrupt event is timed, the board...
Hai, I am using the sd_power_system_off() function for the deepest sleep mode, and my question what function used to wake up my system
I am using nrf52840 board with 17...
Hello, I need to upload the SEGGER script to FANSTEL EV-BT840 (832)-V4 via nRF52832, but there is something wrong with the connection. In my project, it is needed to use beaconing...
Referenece devzone example, : devzone.nordicsemi.com/.../mesh-mac-address
We should set the new MAC value via sd_ble_gap_addr_set before mesh_init( adv_start)
But flash...
Hi, I am looking to develop some code on NRF53. Looks like only Zephyr is supported. Even the most basic example includes some Zephyr files/libs. Reading the docs it sounds...
When I send hid data using below function. (length of data is just 5)
err_code = ble_hids_inp_rep_send ( p_hids ,
index ,
len ,
pattern ,
m_conn_handle );
...
