Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi,
I want to interface wifi module(for example ESP8266 ) with nrf52832.
I need to transfer some data (received through bluetooth) to cloud(AWS).
Can I expect esp8266...
I have been trying to get the Timeslot API working with v15.0.0 of the nRF5 SDK, and have not had any success. All of the examples that I can find are built for much older...
I'm trying to implement the HID service on a custom nrf52832 board, unfortunately I'm running into problems.
Here's what happens: Advertising, connecting to the board,...
Hi,
I think I already know the answer but just to be sure, there is no difference on using printf (with added retarget library) and the app_uart_put() since printf will...
Hi, This is what constant carrier looks like at 2450MHz on my custom board using DCDC disabled
This is with DCDC enabled:
It can also look much worse with no real...
Hi there,
I'm looking at porting (i.e. re-implementing) an Arduino project to the nRF52832 to take advantage of the s212 or S332 softdevices. This chip is a few orders of...
I want to created a connectable iBeacon with nRF52810. I would like to connect my beacon through an app like nRF Beacon app and would like to configure....
* UUID
* Major...
Trying to run the SPI Master application on a custom nrf52382 based device (custom PCB) to communicate with an ADC chip that is taking analog values from a Multiplexer. Not...
I've designed a custom board for the NRF52832. Current consumption is not a major concern, and the pin location was convenient, so I wanted to use P0.00 and P0.01 for I2C...
Hi,
This is a problem report for the Programmer App v1.0.1 on nRF Connect v2.6.1 on MacOS 10.14.2. I have been attempting to use the programmer app with the nRF52 Dongle...
Hi all,
I have a trouble. I use 2 Dev Kit NRF52832. Flash light switch server proxy and light switch client proxy. Issue is when I erase and flash the first time, Client...
I'm developing an application for the nRF52832 using the nRF5 SDK version 15.0.0. We're using the s132 softdevice, the sample secure bootloader (modified to use our company...
Hi, I have been running into a problem where I am getting inconsistently failure to start advertising.
Calling:
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hello, I'm trying to write code to a custom PCB with a nRF52832 using the nRF52 DK and the following wiring:
However, everytime I try to connect the JLink is says...
