I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hello, I used s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
Is there any example to study the central bond?
I use the examples->ble_central->ble_app_uart_c, the following...
Hi All,
I have hardware setup which has four or more beacons in peripheral mode at particular radius ( approx 10 m) and have a beacon in central mode.
The central beacon...
I'm using the Nordic as a BLE solution, and it is just passing along data through the UART to another chip through the UART. However, I'm not sure how to just pass the data...
Greetings,
I am using pynrfjprog (9.0.0) to write a HEX file to an nRF52 device on the nRF52 DK. I am wondering if there is an easy way to verify the write using API.py...
We're looking to implement buttonless DFUs with the NRF52 and are a bit confused how to send 0x01 to the control point of the service. Is this a control point that is already...
I have tried to export a very simple mbed program (blinks LED1 and LED2 and writes to Serial (USBTX, USBRX)) with no success. I am running on an Ubuntu 32 bit distro. This...
Hi,
Is there an example for the Sleep modes and 2Wire on the nrf24LE1 with the SDK? Just found some 2Wire examples with a modified HAL which doesn't seem to work for me...
I'm trying to get the I2C on the nrf24LE1 working. I'm using the modified Library from nAN-20. It doesn't do anything. Can't see anything on the oscilloscope. It's an nrf24LE1...
Hi,
I'm using nRF5_SDK_12.0.0_12f24da and s132_nrf52_3.0.0_softdevice to do the mutilink and it's almost ready. We want to do the OTA on it. I think the mutilink is working...
Hi there,
It isn't obvious from the reference layouts on the downloads page for nRF51822-CFAC if the ground plane is supposed to create a 50 Ohm trace going into the balun...
Hello everyone, i have a task where i need to transfer 50-100kB of data from ble peripheral to a central device. I have read many posts here and i have a pretty good idea...
Hi, I work with the nrf51-ble-driver_win_0.5.0. I changed the heart-rate-collector to discover the characteristic of connected devices. Maybe I'm blind. But the ble_evt_handler...
I want to accomplish something very simple: use a timer to output a continuous square wave on a certain pin, at 30-60kHz or more. It doesn't have to be PWM or anything fancy...
Hi,
I'm working on a BLE application which use ECC.c (Elliptic Curve Crytography). The problem is Keil has found an Error:
._build\nrf52832_xxaa.axf: Error: L6218E:...
Hello Support Team,
I am developing a BLE project use of nRF52832.
My work base on SDK 12.1.0, I have research these workflow, I find that are 3 channel radio when RSSI...
