I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi
I am using timer1 for generating 4khz input to buzzer.It works fine when no ble starts.When advertising starts buzzer shows some flickers according to advertising time...
hi,
im developing an application with peripheral and central.ive used hrs service its working fine initially bt if you keep it idle after some time the peripheral stops advertising...
I am trying to figure out a way to secure my DFU (via BLE) such that someone cannot sniff the and copy my hex code (and decompile). I cannot use Pairing or Bonding as that...
I can use "Pack Installer" to copy example from Keil folder to my hard disk driver, for instance, I copy ble_app_cts_c to my personal folder.
I can build and flash ble_app_cts_c...
Hello there, I have been trying to look at the documentation and the forum but haven't been able to understand the difference between BLE stack event and SYS event. Could...
Hi,
I have a the nrf51822 chip on a custom board and the ble_hrs code loaded on it. Now I would like this custom board to behave as a beacon with the hrs code sending data...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
ble_app_uart_c2.rar
I want to connect two PCA10001's together, one with the ble_app_uart for s120 using sdk 8, and one with the experimental_ble_app_uart for s110 using...
There's no question, I'm just posting this here in the hopes that it helps someone else out.
After I upgraded my Keil packs to the newest SDK (v8.1.0), my OTA FWU bootloader...
I have a problem getting both mesh and persistent storage to work. I am using the code from github.com/.../nRF51-ble-bcast-mesh and followed the document integrating_w_SD_apps...
Hi,
I am using
HW: nRF6310 + PCA10005
SW: s120_nrf51822_1.0.0_softdevice.hex + ble_app_multilink_central (\Keil\ARM\Device\Nordic\nrf51822\Board\nrf6310\s120\experimental...
Hello,
I am a newbie in in using BLE and exploring the nrf8001 DK. I was able to flash PCA 10000 module with updated firmware and it was detected in the master control...
Hi,
I want to read data ,wich is sent from beacon ,using usb dongle,and after this ,I want to send data received from beacon to pc through serial port.
Exist any example...
Hey.
I am wondering if there is a way to disconnect a slave from a master based on the strength on the connection and not when they naturally loose connection.
To give...
How do I block Bluetooth signals ? (I want the signals to be transmitted 180 degrees, not 360 degrees)
I have read it could be done with aluminium foil, but I have not...
