I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
Is there a solution from Nordic available where I can have a LTE-M (or NB-IoT) and at the same time still receive the 1PPS output from the GPS module? It seems to be that...
Hi,
I am working with nrf5340 chip and I want to migrate from NCS 2.6.1 to NCS 2.7.0. I want therefore to apply recommendations: migrate to sysbuild.
With NCS 2.6.1 I...
My device is an nRF52840 running a C Code application that is built on nRF5_SDK_17.1.0 I am implementing a FOTA solution where a hex file fw image and a .dat file will be...
I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...
I'm using a thingy53 on ncs v2.7.0. I turned on CONFIG_ASSERT to try and find issues. This issue pops up randomly, it asserts the program crashes and causes me to have to...
Hello,
I am experiencing difficulties connecting my NRF52840 board to the nRF Connect software. Despite multiple attempts, the board does not appear to be recognized by...
Hi, I'm looking for the public mac address for nrf52840, and i find out that the mac address is located inside the register FICR->DEVICEADDR[0] and DEVICEADDR[1].
DEVICEADDR...
Hello,
I'm trying to do an HTTP multipart POST with chunked transfer encoding but am having trouble sending the headers to the socket. When trying to send, I receive a ...
Hi, I'm having trouble finding out which update caused my application to crash. The build works fine with nRF Connect 2.43, but with the latest version (2.6), it doesn't work...
We're using a noinit section of ram to store a "reboot reason" if/when we need to do a SW reset (i.e. in a watchdog handler).
This works as expected, we set the reboot reason...
HI
SDK Version : nRF5_SDK_17.1.0_ddde560
Softdevcie : S132
I'm looking for resources on DevZone to use AES128. I looked up the content and found that when bonding is...
Hi,
I have been trying to chase down an issue with the flash manager occasionally raising an assertion in mesh_config_backend_init() after a power cycle of the nRF52840...
In my design, I choose to use the circuit suggested in Config no.5, but the USB interface is not effectively identified in the actual test. Through the test, the power supply...
