I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
We have a design using a nrf5340 with a Renesas Wifi chip, That Renesas chip uses a 1 wire interface for Coexistence
We are using Zephyr 3.5.0 and have tried to follow https...
Hi, I have Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H for getting sound and for driving output via speaker I have tas2x63EVM amplifier. Since the nrf5340 audio dk...
Hi,
We want to have some RF-PHY tests on nRF52840 DK.
Therefore, I need a HEX file to make nRF52840 DK get into direct test mode and communicate with CMW270 with UART...
Hi,
I am currently testing the HID Keyboard example in SDK17.1.0. When the nRF52832 is connected to the computer and the Caps Lock key is toggled, it prompts "CAPS ON" or...
I tried to install nRF Sniffer. I followed the instructions here: https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-ble-sniffer/guides/installing_nrf_sniffer.html I...
SDK: NCS v2.6.0
Program Software: v2.6.0\nrf\samples\openthread\cli
Hardware：nrf52840dk_nrf52840 and third-party module(nrf52840 soc)
The program runs normally on...
I am writing to seek assistance regarding an issue I am encountering with the SPI0 interface in the NRF52840 module. The project requires the use of four SPI interfaces, but...
while trying to package my hex file from zephyr and I have gotten the following error
nrfutil pkg generate --hw-version 52 --sd-req=0x00 \
--application build/zephyr/zephyr...
I've been playing around with the MQTT example for the nrf7002dk and noticed that the mqtt_helper_publish function used from the MQTT Helper libraries doesn't handle acknowledgements...
Can someone please, for the love of all that is holy, point me towards some guidance on how to read values of custom characteristics set by another device?
I cannot find...
Hi,
My fw running on nRF52840 (ncs2.4.0, zephyr) develops from HRS sample application. It acts as a peripheral.
In this project, I have a dedicated thread to receiving...
Hi, this should be a straightforward question, I am writing some code to randomly generate a number, and it works fine the only issue is I don't know how to limit the range...
Hi , I try to use the BMI323 sensor . Its working fine for SENSOR _TRIG _DELTA interrupt . I want to use sensor fifo mode for BMI323 sensor , It seems not implemented fifo...
Hardware: nrf7002_nrf5340 Version: ncs-v2.61 Firmware: sample/aws_iot + BLE Mesh initialization ( chat_cli sample example ) Scenario:
My project requires BLE Mesh and MQTT...
Now I am using the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_central/README.html and https://developer.nordicsemi...
