Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I am trying to flash one external module which is actually a BLE having (NRF52832 ) and I am using NRF52832 Development board . By doing all the necessary connections...
Hi,
I'd like to evaluate dual mic recording on three 5340 audio DKs: two of them work as CIS headsets(Unicast server?) and the other one as CIS gateway (Unicast client?...
Using Visual Studio Code as IDE with installed nrf SDK v2.9.0 on MacOS Sequoia 15.2
Terminal reads -
* Executing task: nRF Connect: Build: blinky/blinky (active) ...
I am porting my code from Nordic SDK16 to Zephyr and NRF Connect SDK 2.0. I am working on putting a chip into sleep mode and set up a wake up on a press of the button. Everything...
Hello,
I am working through the Zephyr training modules (These are great, thanks!) and encountered an issue I do not know how to resolve. This issue applies to general debugging...
I'm using SDK17.0.2
I need to keep a noinit variable in memory so that I have the correct flag when I execute the DFU. So I use the following method, but it doesn't seem...
HI ALL,
I used a system off demo and added the following content.
The power consumption tested was around 1uA, which should be normal according to the errata. Then...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. A fatal error occurred on the board when sending some Mesh Model Messages to the smartphone app. It doesn...
I am on nRF52840, and ANCS can get the app name. After switching to nRF52832, you cannot get the app name. The driver of the two chip ANCS is the same, but the Bluetooth protocol...
Hello,
NRF SDK version 2.6.2, tested on 2.8.0 as well
Hardware: NRF7002DK
Sample: Wi-Fi Monitor
When changing Wi-Fi channel using following function
ret = net_mgmt...
Hi,
I'm using NCS version 2.7.0 with nrf9151dk. When I tried out the nrf cloud multi service project with hard coded credentials as explained in this document nrf cloud...
