Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
We have done a lot of projects with nrf52832 with softdevice S332 v5 before.
Now we have a new project to use nrf52840. Can we use the original s332 version? Or do...
I and looking at using an nRF52 device with the nRF Connect SDK version 2.x with a Zephyr Bluetooth LE Controller in a peripheral application where the advertisement data...
Hello,
I am running windows 10 and started the DevAcademy lesson 1, exercise 1 and exercise 2.
Up to exercise 2 item 4 (add a build configuration) everything went fine...
Hello i am using an nrf52840 s140 and i am trying to write a specific event when takes place to the usb port. I am using the usbd_uart example.
It works fine for the first...
I used Nrf9160 to develop a product. Until yesterday, I had been able to connect to the nb network normally. But today, I found that my device could no longer register to...
Hi, I'm looking for help installing the nRF Connect for Desktop 3.12.0.
I've managed to unpack the application EXE and have picked out all the required pre-reqs to do the...
Hi,
I have a problem, When I first initialize Bluetooth and then initialize FDS for writing, it will fail. However, if I first initialize FDS and write data ,it is OK, then...
Hi,
We develop a custom gateway in which we use iMx6ULL and NRF52840. Both are connected over full UART.
We use this NRF52840 as a BLE HCI controller by flashing the HCI_UART...
I'm following the Nrf Connect SDK tutorials on YouTube and I am at step 3 ( nRF Connect for VS Code, 3: Building an application & Exploring windows ). When creating the build...
I have developed an image based on the AWS IoT example which runs on a custom board. The custom overlay exposes some additional UARTs, LEDs, buttons, etc. in custom pin locations...
hi support team,
customer is asking how to add keep alive time in https request header,
i was trying to do this command as below: adding " Keep-Alive: 60\r\n" in XHTTPCREQ...
Hi there!
I've been digging through the code base but could not find a compile option to enable LOG_DBG() type output so that I can observe the JSON formatted packets sent...
Hi,
1. Please solve the problem of high network current registered to nRF9160 (test environment: no network signal)
2. Rf signal: the test current is normal. See Appendix...
Hello,
I implement my own DFU master in nrf52 using SDK11 to replace use of Nordic mobile App. Target to upgrade is also nrf52 but with SDK15.
I have difficulty to get...
