Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I just noticed that setting any of the CONFIG_BT_CTLR_TX_PWR has no effect on the range and RSSI while advertising. Does this config actually do something? I tested...
hello,
I have a DHT11 temperature and humidity sensor connected to Raspberry Pi 4 B. I want to transmit this data from this raspberry pi to another node using 802.15.4....
Hi,
In nRF5_SDK version 15.3.0_59ac345 with nRF52840, the function nrf_nvmc_write_bytes() writes to the same 32bit word too many times.
According to the datasheet:
...
I am starting the Academy SDK course and getting my tools installed. I have VSCode installed (I have used it on many other projects and the "nRF Connect for VSCode" is installed...
Hi ,
When I set CONFIG_TFM_PROFILE_TYPE_NOT_SET=y to disable TF-M minimal mode, KMU SLOT MKEK must be empty right? When the KMU is not empty, the app will enter the tfm_hal_system_halt...
Hi! I have a Thingy:91 v1.6.0 and doing some current measurement on the device. I've disconnected the LiPo cell, and feed the Thingy from an Otii connected to the P3 (Li-po...
Hello,
I have a motion sensor with me and it has 4 pins. VIN, GND, OUT1, OUT2. OUT 1 and OUT 2 gives output voltage of 3.3V or 0.3V depending on a motion. I want to read...
Hello,
Just want to check that is there any mechanism available to check or monitor the expiry date of TLS certificate used in the project? Is there any API available so...
Hi,
I'm extremely new to Nordic (and embedded development in general), but I'm writing some code that turns on various LED colors based on input from an Android app (BLE...
Hi,
I am using mesh sdk version 5.0.0. And I am using sensor server model example to build our application on top of it. I am trying to erase the provisioning information...
Hi,
I have a couple of questions regarding the nRF52811.
1. What's the boot time of the nRF52811 from the power on to call the main() function of the bootloader? ...
Across several NRF Connect SDK versions, I have noticed that when built with the bootloader, the child image is built with the wrong environment and does not use the vendored...
Hi Nordic team,
I am working on a custom board which contains a nRF52840 BLE chip.
The board advertises with 'Nordic Template' code but not with the DFU code.
I program...
hi,
I want to use PPI function for timer trigger to PWM, but I noticed PWM doesn't have TASK_START register, please see the pictures.
how can I start PWM by timer?
...
