I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Using the Power Profiler Kit II with
nRF Connect for Desktop (v 3.11.1) on Ubuntu 20.04 with the Power Profiler App v3.4.3
I'm wondering about the value of the time axis...
When operating in high-voltage mode, the spec says that VREGH,DROP is at most 0.3V . What happens if VDDH falls below the programmed VDD output plus VREGH,DROP, for both the...
Dear Community, Following the Nordic's sample of the (<ncs root>/nrf/sample/caf) the LED module & (CAF) Button module demonstrate the LED states & LED effects (awesome!) After...
Hello DevZone,
I'm using nRF5 SDK for Thread and Zigbee v4.2.0 and trying to test Zigbee OTA example and faced some troubles.
I'm following this guide https://infocenter...
I want to use the BLE Secure connection feature with the following options
CONFIG_BT_SMP_SC_PAIR_ONLY=y
CONFIG_BT_SMP_SC_ONLY=y
CONFIG_BT_SMP_APP_PAIRING_ACCEPT=y
CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY...
Hi
I'm working with a PDM mic for nRF52832 SDK v17.1 on a project and I have a questions about PDM driver working.
Whats the difference between the buffer pointer in nrfx_pdm_buffer_set...
Hi Team
In thingy91---hardware-files-1_6_0.zip, the QM12038 is end of life status now. So do we have any new design to replaced it? Thank you.
www.qorvo.com/.../QM12038...
I just finished the second prototype of a nRF9160 board. First one worked flawlessly, but had poor GPS reception. Rewamped the matching and added SAW filters.
However, now...
I have to switch between several different scanning modes.
I scan in passive mode to get all sensors' advertisements (no connection).
I scan in active mode to get a specific...
Hi everyone
I want use the pwm_driver example of the SDK download at nRF52833 DK
However, some problems were encountered after the migration
I replace the preprocessor...
Hi,
I just started looking around with the NRF52840 development kit and tried to implement simple GPIO interrupt based on the button sample .
I settled multiple GPIO...
Hi All,
If I enable UART module or my code has any stdio functions retargeting to read/write, the debug mode does not work. I am getting the following error:
========...
Hi,
I develop firmware for nRF5340 in VS Code with Nordic toolchain (1.9.1) and NRF connect addon.
Project generates multiple elf files and it seems like only zephyr\zephyr...
Greetings to Nordic team!
I would like to provide BLE security for my application (to my BLE Peripheral device). I am planning to apply the following features such as...
Hi Nodic community,
Could you please help me to flash my Nordic Thingy:91 development board. I was able successfully build Zephyr-based project by following instructions...
