I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
HI
I am using the nrf54l15 SDK version ncs3.0.0 and the Zephyr example. Currently, I am connecting a sensor via SPIM30 and need to read the sensor's data every second, which...
After today's vscode upgrade boards aren't detecting on my pc & on my colleagues pc neither. While same board is getting detected on another one of my colleagues pc. Kindly...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I believe I found a bug regarding PSM (Power Save Mode). Specifically, you can't disable...
Starting with the lbs example from lesson l4e2 of BT fundamentals course, I'd like to send an indication similar to the button (and keep the button). I basically created duplicates...
I am using the nRF9151-DK with the standard (from code examples) firmware . When configuring both P0.13 and P0.17 as ADC inputs, I notice that the current consumption on P0...
I am working with the connected_cs examples on the nRF54L15 DK and trying to swap the GAP roles. In my case:
Initiator = GAP Peripheral
Reflector = GAP Central...
I am working on a Bluetooth Low Energy (BLE) project using the nRF52840 Development Kit (DK) , which has been reconfigured to simulate an nRF52805 chip. The firmware is based...
How can you get the simple channel sounding test going with the bluetooth/cs shell commands?
I've got the shell working over UART and devices talking with each other but...
I tried to add external memory to mcuboot. In fact, I have successfully added it in app, but the same configuration seems to have problems in mcuboot ，mcuboot reports an error...
Hi,
We are developing a hardware and software solution for a locator tag using a minimalist approach. We want to use both, the Google Find Hub and Apple Find My Network...
I maintain an nRF52840 project on the legacy nRF5 SDK and am migrating to an nRF54L15 Bare Metal project.
I could not find a bare-metal “radio test” example, so I’m bootstrapping...
I do connect 52840 DK board to PC through USB cable, sine I want to see runtime log. but meanwhile, I want to use PPK2 to see the current of 52840 DK board, Can I get the...
Hi everyone, I noticed something unusual while testing BLE transmission and reception:
Transmitter: nRF5340DK
Receiver setups tested:
config：Target board...
Hi,
If I build the extxip_smp_svr sample app for the nrf5340dk board. The network image firmware version is set to 0.0.0.0.
To reproduce the issue, do the following...
