Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
hello ,
We use the nRF9160‘s GPS. We see that the 9160 Thingy use a GPS LNA between the 9160 module and the 9160 GPS antenna?
We want to know, whether we can do...
Hi,
I know that the Bluetooth mesh cannot use long range, but I want to know whether the output power of the node can be controlled to adjust its broadcast range？
Thanks...
hi support team,
for ncs, how to add dir to segger IDE like this one.
for example, like keil IDE separating those two .c into two folder in segger.
Regards,
William...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
The instructions at https://github.com/NordicSemiconductor/pc-ble-driver do not allow building the driver or the examples on a Windows system. Following the instructions takes...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, it connects with Mobile or Tablet using Pairing with bonding...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
Dear all:
I am developing a ble scanner using RADIO Peripheral.
I have 2 questions to ask
1.When is the END event triggered?, How does the hareware know the packet is...
I received the hardfault in the following image.
The function at the address 0x00028C44 is:
The hardfault did not occur again after resetting. I'm not sure why this...
Hello,
We have a PIC32 controlling the NRF24L01 with some sucess so far.
But sometimes we get the chip in a state that we can't get off.
We still cannot pinpoint the...
Hi Team,
I am developing an application that nordic chips receive data from msp430 chips by the SPI, and send them out.
Nordic can receive the data from the msp430, but...
Hello everyone,
I tried to add the long press event into my bsp_event_handler without success. I get the normal button press event, but the long button press event is not...
Dear Nordic FAE:
Where can I find the nrf52840-CIAA REACH report?
i can not find it by
focenter.nordicsemi.com/index.jsp?topic=%252Fcom.nordic.infocenter.sdk5.v12.2...
