Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi Team
im trying to change device name during running time..
i can able to change the device name working fine for connectable mode...but if i go for running time non...
the power consumption is about 6.12mW in BT connected, and consumption is about 7.75mW in advertising mode.
is it normal or has possibility to reduce it to extend the battery...
Hi, you must be sick of me!
Now that (somehow) I've got the BLE Secure DFU Bootloader to work on my nRF52840 DK board. I'd now like to load it on a nRF52840 dongle pca10059...
Hello !!
I am using ble_app_becon example code to send some data with device name. On central I'm scanning and searching with device name to identify at central side and...
Heija Guys,
I have a question regarding the usage of the Zephyr BLE and the PWM. I would like to use the Zephyr BLE Stack and the PWM Driver together. The Problem now is...
Hi,
i am working on dfu with NRF52DK. I am facing a problem with compiling a example dfu code "pca10040_s132_ble_debug" .
error message is "cannot find ../../../../.....
Hi,
We bought 2 pcs of nRF52840 Dongles and want to use them to test if a nearby BT device has the correct MAC address.
I've programmed them with "sniffer_nrf52840dongle_nrf52840_7cc811f...
Hello,
I'm using the "usbd ble uart " with twi scanner example to send a sensor value through an arduino 33 ble sense using nrf52832 and it works very well . but when...
Hi,
I'm using the light switch example in the nRF5 SDK as base for Ble-Mesh. I'm using a nrf mesh app for provisioning. I have both client and server model in my application...
When building a project that works with the SDK 1.5.0, I get the following...
r@mint:~/ncs.1.6.0-rc2/nrf/nordic_assist/nordic$ west build -b nrf9160dk_nrf9160ns
[0/12...
I am working on a custom board for the nRF9160 and currently have a DK and a thingy.
I need to make a serial interface available on the DK, thingy and a custom board I...
I want send data from Mobile over established BLE Mesh Network (through Proxy node to all nodes in the network) and also get data from BLE Mesh Network.
Data is customised...
I have not set nrf5340 i2c2,uart2 to work .
,in prj.conf ,add below configure:
CONFIG_SPI=y CONFIG_NRFX_SPIM2=y
in prj.overlay ,add below configure:
&spi2 { status...
I am working through the Getting Started documentation for the nRF Connect SDK 1.5.1 on a Windows 10 machine running SEGGER Embedded Studio Nordic Edition Windows x64, Release...
