Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hello Nordic Team,
We need to start RF performance tests using CMW500. we have access to UART pins of nRF52840 in our DUT which can be used to connect UART-USB adapter to...
Hello Nordic, I am using
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
Can I transfer 8208 bytes on I2C with nrf52832 with EasyDMA, ignoring the MAXCNT...
Hi,
I try to understand the power consumption of the UDP example for NRF9160 with PSM.
I'm using the default configuration: RAT="00000000", RPTAU="00100001", no eDRX,...
Hi all,
I am trying to interface a BLE mikrobus module onto a Yocto based Linux SBC. I need to use Zephyr's hci_uart example to flash it onto the module, the mikrobus...
Hi Dev Team,
I am running a program that takes in sensor data at 10 min intervals and publishes it to my server through MQTT at 1hr intervals.
I have different threads...
Hi, I am using Zephyr BLE stack to check the HCI testing og the nrf52840_pca10056 module. I am useing Windows Subsystem for Linux for Ubuntu toolchain. While using the make...
Hi,
I am planning to buy a nrf9160-DK to build a BLE LTE-M gateway. I would like to ask if the gateway is able to communicate with a private MQTT broker/server instead of...
my project is freertos+nrf52832 based the templete in SDK; A sensor pin is connect to P0.17, and I configure it low to high level trigger interrupt.In the handler I will call...
Hi all,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. I want to observe packages sent by the client and packages arriving at the server...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
Question:
I am testing SERCOMM module and nRF9160-DK, but there is difference in registration procedure .
When...
Hello, I migrated codes that I believed to be relevant to the UART output to a new project, namely the uart_init function and others, and it worked in main.c, which is where...
I am trying to use the connectivity firmware with an NRF52840 dongle to communicate with an nRF52840-dk through the nordic UART service, but I am unable to use the pc_ble_py...
Hello,
I am curently working on project with a nrf9160. I will use the nrf9160 as modem controled by a nrf52840 and command AT. I will send data true GSM every 12 hours...
