Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I am using a nRF52840 dongle to communicate between a laptop running Ubuntu and a phone running Android.
Right now I set up a UART-BLE communication using an...
Hi
I've been developing using an NRF52 DK and have moved onto my own design board, I have one small problem which I'm unable to replicate using the DK. On my own board,...
I have tried to study the behavior of the QSPI and the external flash. I noticed that the QSPI_CONFIG_READOC and QSPI_CONFIG_WRITEOC settings in sdk_config.h cannot be set...
Hello,
I'm developing AoA/AoD feature, accoring to manual, the nrf52833 uses S0CONF and S0MASK to automatically determine if the part S1 exists in the packet or not. I tried...
Hi everyone,
We are designing a low power PCB based on the nRF52840 BLE. At the moment the device is advertising with an interval of 1s and a timeout of 3min (advertising...
Hi everyone,
I am looking the ble_app_template_pca10056_s140 example and I have a question regarding the advertising_start(erase_bonds) function in main();
When you call...
Hello,
We are in the final stages of our product development and we would like to add a feature used during assembly to give some sort of confirmation that everything is...
Am trying to evaluate the nRF9160 + nRF52840 combo as in the thingy, we want to send an sms to the device and reveice back its GPS location. SMS is spectically requested for...
Hello,
I want to prevent a scenario where I successfully perform a DFU with a faulty firmware image. I have a bootloader that handles firmware updates both for the NRF5...
Hello all,
I am working on low power sensor development with nRF52833 as target. I have some questions but I'm not sure it this was addressed in some other posts.
1. I...
Hi,
I'm integrating some c++ code using ble_app_uart example as base. The code has some cout << "text"; kind of outputs that seem to go to uart by default configuration...
Hi. I'm trying to find out the real consuption of the nrf52832. I have two questions after consulting part "7.2.1 CPU performance" of the datasheet.
1- Is there a difference...
Hello,
I have recently used the new toolchain manager to upgrade to ncs v1.3.0. Now I am using Segger Embedded Studio to flash an nRF9160 with the at_client sample. My issue...
Hi ,
I have an Android app that acts as a Central mode and Nordic nRF9160 as peripheral mode.
Once the connection is established , App will read the characteristics...
Dear all,
Pushing the hardware to the limits, I came up with a question about the architecture of the microcontroller itself: Can two different instances of SPIM start...
