I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
hello nordic
i am working on a project with nrf52832
we need to be reading and writing to 2 different tags near the system
is there a Nordic hardware for such...
Hi. I'm trying to use command line tool, but an error occurred as shown in the picture below. Let me know why.
J-link was connected normally in segger embedded studio.
Hi All,
I need to implement security in Bluetooth. I have seen many threads but I could not get proper information regarding how can I implement or add security in a project...
Hi,
I am using the nRF52840 chip and supply iam giving from coin cell(3V). So i want to measure the coin cell voltage level monitor with nrf52840 ADC pin.
kindly provide...
Hi,
I was trying to program my sample to nRF5340's flash using nRF connect v3.4.1 and got this problem:
21:06:02.948
Application data folder: C:\Users\tuan.duong\AppData...
Hi everyone,
I was wondering if you have any advices or recommendations regarding the best type of debugging devices, or ways of debugging, for the nrf52840 Dongle, from...
I want to optimize my receiver power by putting the controller in sleep mode, that is ;-
NRF_POWER->SYSTEMOFF = 1;
And want to wake up the controller only when it receives...
When I try to increase the CENTRAL_LINK_COUNT from 8 to 9 in ble_app_multilink_central example, I got this error NRF_ERROR_CONN_COUNT . Is there a way to increase the max...
Hi,
I wrote a code using gps_controller.c on my thingy:91. However, i could never get a GPS FIX so i decide to try the GPS sample but it doesn't work neither.
I tried...
I'm using nRF52 DK to develop a BLE/UART application. My code is based off of the ble_app_uart peripheral example. In both my code and the default code, I get -0.1uA on the...
I am used NRF52810 controller, I wanted to know about there is possibility to work iic slave and iic master ( vice versa ) in single program ,can have any possibility about...
Hello, I have some questions regarding what MCUs to choose. I have a project which requires some controlling of external LEDs, Bluetooth communication as well as some extra...
I have used nrf52 module and it was working correctly. while debugging my PC was restarted for other pc issue. after the reboot i opened my project file my main.c file exist...
Hi! I am going to work on a project that uses a specific sensor which produces voltage outputs between 250 mV and -250 mV. Can someone help me with ideas to detect the negative...
