Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hey! . I am new to embedded developing and was trying to familiarize with nrf52 DK .
Issue : When i try to run the BLE examples in sdk after clicking " download and debug...
Hello! I am having issues dfu from the huawei p30 lite. with nrf51. Tried with nrf connect and nrf toolbox.
Dfu progress stops at 2-3% when uploading. Error Remote dfu error...
I am unable to connect the nRF9160DK to the cellular network.
I have gone through the "Get started guide" (working in Linux) and I have been able to install the SDK. I have...
Hi, we have faced with the same issue as many nRF52 users, debug interface (DIF) will stay active after flashing and high (~3mA) continuous current remains, Power cycle will...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
In BLE peripheral example ‘ble_app_template’, it is for doing Advertisement...
hi... folks
I am working on multilink central example, i have modified this example to multi link central uart ,where i can able to connect to multiple peripheral to a single...
Hi,
I am using NRF51822(PCA10028) ble_app_uart example , I need to change the name of the BLE device during Advertising and store the name in Flash so that when ever the...
Hello,
I am trying to establish a network to send data over the boards.
I tried using examples in Ble_central and Ble_peripheral, but in those examples they would stay...
Using the esb tx fifo, it appears to change the ESB_MODE from PTX to PRX, and changes the esb channel to some other value. Is there any way to setup the radio so that it doesn...
Hello,
I am working with nrf52840. I have read how the SAADC example works at https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v13.0.0%2Fnrf_dev_saadc_example...
Hi everyone, I'm having trouble deciding on the "best" / "most sane" way to interface two I2C sensors with the nRF5832. Both sensors are on the same I2C bus. The first sensor...
Hi Bro
I have a project need to use BLE + ESB Concurrently, actually I have did it in my previous project
but seems it has problem in new SDK
In my old project: SDK11...
I'm using the nRF52 DK (with an updated firmware) to program an external target (using the "Debug out" connector). It looks like the programming speed is limited to 1MHz:...
