Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hi,
I have been using nRF24 in many projects with Arduino. So far quite good experience.
Now I transfer to STM32 and have a strange problem, I cannot send with STM32 as...
Hi,
Has anyone tried connecting the grove_display to the nRF9160?
http://wiki.seeedstudio.com/Grove-LCD_RGB_Backlight/
I have tried the code below
https://github.com...
Hi All,
I'm trying to understand certificate goes where from AWS-IOT to certificate.h.
when setting a new device, I have these 4 certificates:
also the ROOT CA contains...
I have a custom Characteristic in my GATT that is sending data in Notify mode every 30ms.
In my firmware I use timer to do this with something like this :
Everything...
I'm looking to test the DPPI peripheral on the dev-kit, and to that end I though a good example would be to setup the DPPI peripheral to trigger an event when a button is...
Hi, I am new in the development. I want to interface the relay withe ble module.
But not able to do that. Please any one help me to interface the relay. Thanks in advan...
Hi,
Asset tracking example used to work for me, after reinstalling my environment I get nrf_cloud_connect failed: -111
this is the output from the LTE link monitor:
...
Hello,
I'm using the same SDK used on the Thingy:52, compiling with GCC. I'm using the Rigado BMD-350-A which uses the nrf52832.
I'd like to use P0.09 and P0.10 as GPIO...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
Hello,
I'm developing a custom application based on SDK 15.2 on nRF52 using softdevice S132 v6.1.
In my development, I want to ensure timestamp synchronization between...
Hi,
I am using NRF52 SDK 15.3 on nrf52840 Preview DK
I am using BLE to transmit data, I want to use PPI to get readings off of SAADC but using 'app timer' instead of TIMER...
I'm currently on a question for which the documentation here can't help me.
If I'm correct, the Dual-Bank Update allows to retain a safe copy of the old firmware image...
