Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
My application runs perfectly for like 14-15 hours and then when trying to connect to go into RRC connected mode to transmit the modem crashes with following error...
Hello,
we noticed for one of our boards that the nRF9160 is not able to startup with a floating MISO pin on the SPI where the flash is configured in device tree (SPI1 /...
We have a custom board based on the nRF52805 that does not have a LFXO, instead relying on the RC. We are using NCS 2.6.1.
We see current spikes every 4 and 8 seconds that...
Hi,
as mentioned in the title, when using the official vscode extension (nRF Connect for VS Code) for debugging and stopping a debug session, the target state does not get...
Hi：
I have the following hardware structure：
FPGA < -- SPI -- > NRF5340 (TX) -- ! ( ESB ) ! -- NRF5340 (RX) < -- USB -- > PC
Due to the nature of my application, I need...
Hello!
I am trying to collect data from an nRF52832 device which works as a peripheral to another device nRF52832 which operates as both Central and Peripheral.
Description...
Hi,
I am downloading GPS Almanacs from U.S. Coast Guard Navigation Center web site to inject into the modem using nrf_modem_gnss_agps_write() . Below is current almanac...
Hello,
I need a way to decide on which Api to use for UARTE (configured as uart1) once in main(). I am not intending to switch between them nor to use them at the same...
I am currently working on a project to migrate to the nRF Connect SDK. We are using the NRF52840-CKAA-R7 package of the nRF52840. However, I have not been able to locate the...
I'm develping application on nrf52832 with nrf5SDK v17.0.
The connection interval is set to 12 to 16.And the conn_sup_timeout is set to 1000.
The condition happened frequently...
As I understand it, any applications using the modem libraries on the nRF9160 must be built in the non-secure domain. The MCUboot and TF-M needs to be in the secure domain...
Hi.
I need read the external voltage in input P030, and the battery backup voltage in P031.
If I read using only one channel, the P030 (AIN6 ) the value that show...
I want to send key strokes between two pic 16f887 microprocessors using the nRF24L01. I assume I can use ShockBurst to do the job. The master sends the key strokes and the...
Hello,
In the nrf5340_aduio application. I found it support 2 channels both of output(mic signal) and input(audio signal) on the USB device.
But i want to know if it can...
Hi,
I am debugging an application whth MPSL enabled and occasionally get this error:
E: SoftDevice Controller ASSERT: 48, 190
E: ***** HARD FAULT ***** E: Fault escalation...
