I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hello,
we need to SPI interface of a display controller RM6909 (AMOLED for smart watch) with the NRF52832 processor.
Could you please share us the source code for that...
Hi,
We are currently evaluating the Tracker V2 application.
We would like to increase GPS accuracy, before the nrf9160 returns status GNSS_EVT_DATA_READY. No problem...
hi nordic team，
i have use nrf52840 develop a product ,now i need make sig authentication to sale it .the sdk version i use is 16.0. i m sure it can pass the ble5.0 authentication...
Hey ,
Is there a way to connect and send commands directly using the dongle to the NRF52832?
If so , where can I find a protocol for the communication ?
Hi,
I am testing the sample "machine learning" (from the template nrf/applications/machine_learning) on Thing52. And connect the Thingy52 to the central_uart on nrf52DK_52832...
Hi, in my project I'm using fstorage library to store some information that should be kept even after the firmware update.
For this we are reserving the memory address as...
Hi,
At work we are developing custom HW with an nRF9160, using NCS 1.8.0 for now, but I have confirmed the following behaviour on a nRF9160 DK with NCS 1.9.1 as well.
...
Hi,
after connecting to our mqtt broker I set nrf9160DK to data mode and publish data to our mqtt broker:
After this LTE link monitor is not accepting any AT commands...
Hi,
I am trying to enable extended adverts, when the call to bt_le_ext_adv_create is made, it always returns:
Using the following code:
My custom service has the...
Hello,
I have three devices that use UART, connected to an nRF52832 that I'm using NCS 1.6.0 to program. Since the nRF52832 only has one UART module and Zephyr has no native...
Hi, when following the tutorial, https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial i ran into problems...
hi, I want to use 52832 Comparator function, SDK only has "low power comparator" demo code. Setting reference voltage in MCU, just compare one GPIO with this voltage.
But...
Hi
I was creating a function to send i2c data trough sensor that I use. But when I double check the communication, there is a part that doesn't works properly. So as you...
Hi, Is it possible to enable and Different log level from Zephyr cli using Zephyr Logging API? i am using
LOG_MODULE_REGISTER (AWS, 3 );
I want to change or register...
Soft Device v7.0.1 is used. Timer instance 2. I use a "Timer-PPI-ToggleIO" to toggle an output pin to make sure the pin will toggle at the right time. The timer interrupt...
