We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Following the guide posted here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.1.2/nrf/doc_build.html Generate this error:
C:\ncs\v2.1.2\nrf\doc>cmake -GNinja ...
One of our customers provided their own SIM card for our nRF9160 based product, and the system works but they have been having higher than expected power consumption.
We...
Dear support,
It looks like there are 2 compilation issues in NCS 2.1.2:
ncs/zephyr/arch/arm/core/aarch32/cortex_m/fault.c : fault_show doesn't compile when CONFIG_FAULT_DUMP...
Hello,
I have a strange problem and after having searched in this forum and tried to realize proposals which were given at other tickets here I need support for solving...
Good morning,
I have nRF52840 Dongle.
I am looking for a tool that will allow me to connect to a BLE device based on its name.
Need:
- find the device,
- connect...
What I'm working on:
I'm working on a small project using this nrf52840 module:
www.minew.com/.../
Access to source:
If it helps to understand my issue, all the design...
In the function "bt_scan_filter_status_get(bt_filter_status *status)" [file: subsys/bluetooth/scan.c #1302], the variable
"status->manufacturer_data.enabled" is not updated...
hi devzone
I've trouble starting nRF Connect for Desktop v3.12.0.
I'm using nrf52-dk / pca10040 board and nrf5_sdk_17.1.
when I run the program "nRF Connect for...
Hi,
I do have a question about PCB layers. I did read it is better to use a minimum of 2 layer PCB, but why is this? By example is a single layer also OK?
I'm trying to...
Hi Team,
We are using Nordic connect SDK nCS 1.9.1 & nrf52833
currently have not changed any clock frequency they're at default settings, we want to know what is the...
Hi, quick question.
Software: SDK 17.1.0 with segger embedded studio
Hardware: nrf52833-dk
Background: I read that it is possible to take iq samples of the payload....
Trying to using IEEE-802.15.4 on nRF52820 with SDK-17.1.0, Librarie 802_15_4/raw/802_15_4_lib_gcc.a.
nRF52820 n ot support FPU so set -mfloat-abi=soft in Makefile
Encounter...
I successfully completed all exercises from DevAcademy using nRF Connect SDK v2.0.0 and nRF Connect SDK v2.1.1.
However, when I tried to experiment with DevAcademy Lesson...
I have not done anything with the SDK for a while so I updated Segger Embedded Studio to the latest: 6.40 and the latest nRF SDK 17.1.0 and built my project and I only needed...
Hello together, I'm searching for a way to go I max low power mode possible an then wake a from one of three reasons:
Timer/Clock
NFC-Field
GPIO
I searched the...
