Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello!
I'm trying to set up data transfer between nRF 52840 dongle and KX134 accelerometer from SparkFun. Currently I'm running the WHO_AM_I test only. The code is derived...
Hi all,
What's happening?
System reboots when "flash_erase" is called with parameters offset 0x1f000 and size 0x1000
Setup:
NCS v2.0.0
nRF52832 with 512K flash...
Hello,
Been chasing this undefined reference to `__device_dts_ord_XXX' issue around for awhile now with no clear path forward. What I am observing is extremely similar to...
Hello,
I am working on Thread client server based network. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development hardware is nRF52840-DK, HW Version 2...
Hi,
I am using nrf toolchain v2.0.0, and am testing the dfu-ota example over BLE by following the below link ( ) . howveer for fast boot up, i am using "
CONFIG_BOOT_VALIDATE_SLOT0_ONCE...
It is possible to change the partition table through a FOTA?
Is the partition table stored somewhere on the device, or is it merely used for linkage? If it is linkage only...
Does anyone know how to use the CMSIS-DSP FFT library on a nrf52832?
I am using the nrf Connect SDK and it seems all of the examples are for nrf5 SDK.
I am looking to...
i use the ubuntu20.04 and open nrfconnect-3.11.1-x86_64.appimage through proxy successfully
then i install and open the toochain manager , there is not include NCS 2.0...
We are developing a new product and plan to use nRF52810. As I understand nRF52 will be supported for production in the new nRF Connect Release (1.3.0) that will come soon...
Hello,
Our application requires the device to go into deep sleep and wake up every 24Hr or on the Accelerometer interrupt. We were able to obtain the sleep mode and wake...
I'm trying to migrate my project to NCS 2.0.0 but having an issue like below:
c:/ncs/toolchains/v2.0.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/10.3...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi We have designed some boards with ESPRESSIF WiFi BLE Module ESP-32-WROOM-32E for control and monitor.
Is it possible to connect esp32 to nRF21540 to extend range ( such...
Hi, I am using nRF52840 and communicating with Simcom GSM( Sim7600g ). 1- Is there any example code/ Library to connect with the MQTT server?
2- Can I use this example code...
I found my thread device to have quite a large latency so I analysed the communication and found out that the device is actually timeouting and retrying before listening for...
