Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
On the nRF5340-DK, i'm succesfuly using the example code:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/peripheral_uart/README...
Hello Support,
I just started to play with the self provisioning "Mesh-Demo" sample to get a hang of the BLE Mesh. Since I am working on the nRF52480 DK and don't have a...
Is the Common Application Framework considered ready for production use? The fact the "Common Application Framework overview" page links to "Common Application Framework preview...
This is a follow-up to a previous ticket https://devzone.nordicsemi.com/f/nordic-q-a/83842/error-when-building-configuration-for-non-secure-boards , the problem persists and...
I have connected a nRF5340 DK board which the Programmer can connect to. I then drag the two .hex files for the Heart Rate Monitor demo over to the File Memory Layout window...
I've was able to use brand new PPK2 to make test measurements few days ago and it was working fine. I've connected the unit today and software have issue recognising the device...
After reading through the nRF21540 datasheet, I have a few questions.
1. Is section 5.5 saying that even though the spec for VDD is 1.7-3.6V, VDD needs to be between 3.45...
Hello everyone,
I'm now having a problem while using nrfx_spim_xfer on nrf52840. I want to use nrfx_spim_xfer with a callback when transmitting is done.
My setup code...
Hi,
For a development evaluation, I am looking to program nRF52833 to have it interface with "IS25LQ040B" serial flash chip through SPI-1. I found lack of examples and...
I am using the "nRF5_SDK_17.0.2_d674dde" for nRF52 development.
Would like to get the SoftDevice and nRF52 device for confirmation after OTA.
1. When using the sd_ble_version_get...
I am trying to send a OnOff output cluster information to Co-ordinator when a button is pressed in the nrf52840 DK. The problem is the during the initial registration, the...
Hi.
i want to power my nrf52840 with 2 AAA batteries i connected them directly to the module. Is there any Bluetooth signal strength difference when battery voltage drop...
Hello !
I have taken example /examples/crypto/nrf_crypto/aes/aes_ccm
and modify & g_nrf_crypto_aes_ccm_star_128_info instead of ccm
and initialization is failed
...
Hi everyone,
I'm looking for the max output current VDD can source (REG0) when the NRF52833 is configured as High Voltage Mode (see pic for context).
The NRF52840 has...
I need to send bulk data to an MQTT topic on a server hosted by AWS. I'm trying to use datamode option the serial_lte_modem sample but I'm running in to lots of problems....
