Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
We are currently looking into using the nrf9160 for a smart meter gateway like solution. It is of particular interest to us to know if we would be able to achieve compliance...
Hi all,
I am having issues with the nRF connect programmer that is used to flash the mcu.
I have installed the software my nRF connect version is v 3.10.0 (It is not available...
I installed nRF Connect and inside it I installed Programmer. When opening the programmer I get the following exception:
And system report:
I already tried following...
Hi,
I currently have a working project with BG96, embed TLS and LWM2M.
I'm investigating some problems that occur when the connectivity is interrupted during TLS handshake...
Hi !
In nRF9160, want to implement nrf_mode_lib for modem. Therefore, need to select non-secure(ns) board.But want to set UARTE2 as secure. As UARTE2 provides communication...
Hello!
I am completely new to development with the nRF52DK.
Today I spent the entire day trying to set up the IDE and enviroment to make my first application, but that...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello All,
I am using the BE33 (nRF52833 based) module of the Celium Device. I am able to flash the code by using SWDIO and SWDCLK pins. Also, I have tested the BLE advertisement...
Hi,
I am running into this issue when receiving over uart where the byte received is always one byte behind relative to the byte sent by the sender. The byte received is...
I've never been able to get >= 10.13.0 of the nrf tools working. The previous versions work fine on my x86 mac, but there are a series of problems with the newer tools. First...
Hello,
Is there a way to configure mcuboot to allow updates to the bootloader itself? That feature is supported in Nordic's bootloader, but I haven't been able to find...
Hi All,
We are using NCS v1.7.1 on our custom designed nRF52840 board. We have a touch screen interfaced with I2C to our device. There is one more controller connected on...
I am making a "program that keeps multiple software in Flash ROM and reads arbitrary software according to instructions".
When I open the hex file with a text editor, the...
So i have my nRF5340 DK and have been pretty successful in getting my Mesh working with some Thingy:52 devices, some Adafruit Feather devices and some Sengled Lamps.
Groovy...
I am trying to read from the LIS3MDL sensor using spim on the nrf52840 dongle. I gave the rx buffer with the length of 7bytes. Whenever i tried to read from the sensor, I...
