Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
We have a situation where the network core of the nRF5340 has been given control of Port 0/GPIO pin X (GPIO0->PIN_CFG[X].MCUSEL = 1 on the application core). The network core...
I have 2 dongles that I've somehow managed to brick (I don't remember the details on how i did it). One of them goes into DFU bootloader mode when I plug it in but shows up...
Hi,
I am modifying the code to asset_tracker_v2 on Thingy91 to send data to my own server instead of Azure / AWS / Nordic Cloud. I am getting error code -35 (EDEADLK) when...
The discussion in https://devzone.nordicsemi.com/f/nordic-q-a/79364/maximum-number-of-bytes-that-can-be-used-in-beacon-advertising suggests that we should be able to populate...
As far as I understand I should be able to use the nrfutil (6.1.x) on a Rpi 4B to update any of the nordic semi devices nrf5x supporting bluetooth (i my case nrf5340) Will...
I am new on Bluetooth. Currently I am playing with BL5340 development board. I need a firmware to test Bluetooth data transmission latency between two BL5340 modules. Could...
Hello,
I'm running the Asset Tracker V2 NCS 1.7.0 conected to the nRF Cloud. I'm using a Thingy:91 with external GPS antenna.
The GPS position is being correctly aquired...
Hello ,I am starting new development in Nordic environment and my system configuration is intel i3 with 8gb ram.
Still it is way too much slow to open nrf connect for desktop...
Hello everyone,
i want to use the 52810 to write into a SD -card, i use a slightly modified fatfs example.
The problem is, the SD card will not initialize as the p_event...
Hi, I'm trying to implement a sleep mechanism in my app. I based my code on the Power Management Example.
I use a button to put the app to sleep and the same button to wake...
Hi Team,
I am working on a project. It requires nordic chips (slaves) to communicate with msp430 (master). I use the nordic example SPIS as the initial code of the nordic...
My project consists of STM32 + 4G + nrf52833. When the 52833 firmware needs to be updated, the cloud service will send the 52833 firmware to STM32, and then STM32 will send...
Hello all!
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My developmnet board acts as a central whereas my phone as peripheral...
Dear team,
1. I am using the Ble_app_uart example from the SDK.
2. I had received the data successfully from the nrf_connect app.
3. Once the data was received over...
