Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I'm running into an issue in which I cannot initialized the I2C drivers on an Arduino Nano 33 BLE (nrf52840). The output from error logging is
I have this prj.conf file...
Hi. I am using timers and PPI to do frequency counting.
The basic process is for 1 PPI channel to incriment a timer, and then a second PPI on a second timer to stop the...
I build device based on Fanstel module BC833M with pcb antenna.
Communication with this device is very bad. I have test the same code in BC833M and origin Nordic devkit...
Hi,
First off, I'm very new to the nRF52 development so I'm suspecting to have done something wrong...
The datasheet of the nRF52 832 states a current consumption of 0...
Hi,
I have been tryring to identify the characteristic who is requesting a read. To do so, I implemented the read authorization request. Here is my code:
Basically...
Hello,
I'm trying to receive an inverted UART signal on the Arduino Nano 33 BLE (NRF52840). I've been able to invert the transmit signal okay using two GPIOTE channels and...
in ble send data period ,nrf 5340 CPU seem to be shared only by ble send
data ready and data read in ble not send period can equal ,this mean every data come from ecg chip...
Excuse me:
I'm testing the maximum rate of ble_app_uart。
1、Can the nrf connect app on IOS initiate the update of MTU and PHY?How to update MTU and PHY on IOS nrf connect...
I use nordic5340 SPI read ADS1298R ecg data, using nrf5340 p0.13 to connect ADS1298R data ready pin . when ADS1298R data ready pin high to low mean ADS1298R data ready .i...
Hi guys I am new to Nordic, just made a DevZone as the technology isvery interesting to me. So far I have been playing with ESP series but I know nordic is in a class of its...
Hello everyone,
I have been working for a few days with nRF52833DK building a BLE mesh where one of these microcontrollers is a client node or a server node.
However,...
Hi,
I have several questions about the dongle board.
1. Why should the p0.19,20,..,25 be connected to the reset pin?
2. what is the difference between the reset button...
Hi, All,
I saw the options for S2 and S8 in conn.h of ncs, but i don't know how to use it.
And I want to test the relevant data and differences between S=2 and S=8 broadcasting...
