Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
DFU secure bootloader ( secure_bootloader/ pca10040_s132_ble ) using segger embedded studio version 5.50
Am using SDK version 17.0.2 for BMD350 nRF52832 module
Already...
Hi there,
I was able to successfully compile and run the "BLE HIDS keyboard" example on my nRF52832 using Segger SES 5.44
My Nordic chip is connected via UART Rx/Tx to...
Good day
I use NRF52840 + SDK v17.0.2. My application relies on _gls example and mainly copies its security settings ( also uses peer manager ) except I use MITM protection...
Hello Dear!
Please look at the red area in the picture.
The C9 820PF, it's no commonly used,We buy it very hard.
Can i modify C9 820PF to change C9 1 nf in desgin?
I've read quite a few threads where people are asking for help getting NAND Flash to work with their devices, only to find out they are not supported. I see that only NOR...
Hi
I am using nrf52832 to develop a ble hid device with tile function
I merge sample code ble_app_tile to ble_app_hid_keyboard example
I use the advertising_init function...
The firmware crashes when passing the ble_stack_init() when the firmware is download but in debug mode it works fine. The screen shots below shows this event.
We are using...
Hi there,
For my POC test, I need to send a max 255 bytes payload data from a client to one or many servers. I use two nrf52832 DK boards, BLE sdk 17.0 and BLE mesh 5.0...
Hi,
I'm using PWM driver DEMO5 to change the voltage of IOs.Now I need different voltage ranges.
Here is my code:
The voltage will change when button is pushed,but...
I have followed this tutorial ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0#h185sjwm5882m1bcimiad82dnf4kcy0b...
Hi,
I am scanning device using Provisioning service, would like to know after Provisioning, does device contain Provisioning Service in it or not.
Does only Proxy service...
Hi everybody,
I am using nRF52832/40 with SDK 15.3 and softdevices S132/S140 v6.1.1.
One of my devices is performing active scanning, therefore sending scan requests,...
